HyperCube 3D Printer/CNC
par Tech2C
Fichiers imprimables (27)
-
stlX_Carriage_beltclamp.stl
114 Ko · 564 873 téléchargements
-
stlXY_Motor_left.stl
286 Ko · 564 532 téléchargements
-
stlY_Shaft_Clamp.stl
245 Ko · 563 380 téléchargements
-
stlY_Shaft_Clamp_Left_Motor.stl
245 Ko · 562 449 téléchargements
-
stlE3D_clamp.stl
265 Ko · 562 856 téléchargements
-
stlSpool_Axle_Clamp.stl
308 Ko · 561 992 téléchargements
-
stlDual_bushing_holder.stl
181 Ko · 562 359 téléchargements
-
stlXY_Motor_right.stl
283 Ko · 562 021 téléchargements
-
stlY_EndStop.stl
105 Ko · 561 070 téléchargements
-
stlXY_Idler.stl
315 Ko · 561 340 téléchargements
-
stlBed_Support_v1.1.stl
84 Ko · 560 069 téléchargements
-
stlZ_EndStop_Adjust_v1.1.stl
80 Ko · 559 208 téléchargements
-
stlZ_Motor_v1.1.stl
323 Ko · 559 344 téléchargements
-
stlZ_nut_mount_v1.1.stl
360 Ko · 558 833 téléchargements
-
stlFan_Duct_v1.2.stl
143 Ko · 556 052 téléchargements
-
stlXY_Joiner_v1.1.stl
649 Ko · 556 546 téléchargements
-
stlXY_Clamp_v1.1.stl
181 Ko · 555 321 téléchargements
-
stlE3D_sensor_mount_v1.2.stl
211 Ko · 542 016 téléchargements
-
stlE3D_mount_v1.1.stl
719 Ko · 543 320 téléchargements
-
stlX_Carriage_v1.2.stl
995 Ko · 544 015 téléchargements
-
stlZ_EndStop_v1.2.stl
181 Ko · 521 516 téléchargements
-
stlZ_Carriage_clamp_v1.1.stl
68 Ko · 521 296 téléchargements
-
stlZ_Shaft_Clamp_v1.2.stl
178 Ko · 521 393 téléchargements
-
stlZ_Carriage_v1.1.stl
281 Ko · 521 072 téléchargements
-
stlBowden_Idler.stl
95 Ko · 278 297 téléchargements
-
stlBowden_Knob.stl
157 Ko · 278 003 téléchargements
-
stlBowden_Motor_v1.1.stl
791 Ko · 264 361 téléchargements
Description
This is a CoreXY 3D Printer and CNC. (Last updated - 18th Jan 2020)
Upgrade your 3D Printer to this frame! Re-use your motors, electronics, hotend, heatbed, etc...
Watch how the HyperCube came to be:
https://www.youtube.com/watch?v=n2jM6v3E7sU&list=PLIaArjwViQRVAERWRrYfe9rtiwvvRGCzw
I wanted to reduce the weight of the moving mass as much as possible. As the entire X-gantry is moving in the Y direction, the rails for the X axis should be light too. I chose to use 10mm anodised aluminium tubing, which is half the weight of 8mm steel rods.
And have since moved to Carbon Fibre tubes, which is one eighth the weight of 8mm steel rods.
Marlin 2.0.1 Configuration.h and my built firmware.bin files attached.
BOM
Frame:
T-Slot 2020 (Slot/Type 6) Aluminium Extrusion Profiles for X200 x Y200 x Z155 print bed area
(Note: If you intend to make a larger print area, then increase the length of the 2020 extrusions AND rods for each axis by the difference)
Buy from Banggood - Silver, Black or Buy from Amazon
- 4 x 340mm (X)
- 4 x 303mm (Y)
- 4 x 350mm (Z)
- 2 x 285mm (Bed)
- 1 x 135mm (Bed)
Fixings
- 60 x M5 x 8mm button head screws (Amazon)
- 60 x M5 x 10mm button head screws (Amazon)
- 2 x 100pcs T-Slot M5 hammer nuts
- 3 x 10pcs Aluminium Corner Brackets
CoreXY + Z + Bowden:
- 2 x 8mmx300mm Hardened Steel smooth rod (choose 300mm length) for Y axis
- 2 x 12mmx400mm Hardened Steel smooth rod (choose 12mm size) for Z axis
- 2 x 10mmx360mm Anodised Alu tube OR Carbon Fibre Banggood or Amazon for X axis
- 1 x 10pcs Self Lubricating Bushing or for Carbon Fibre tubes Igus JSM-1012-10 for X axis
- 2 x LM12LUU linear bearing for Z axis
- 2 x LM8LUU linear bearing for Y axis
- 1 x T8 300mm Lead Screw for Z axis
- 1 x 5x8mm Aluminium Flexible Shaft Coupler for Z axis
- 2 x 10pcs F623ZZ Flange Bearing
- 1 x 5M GT2 Belt
- 1 x 2Pcs 2GT-20 Teeth Timing Pulley
- 1 x Knurled Drive Gear for Bowden
- 1 x PTFE push fit connecter for Bowden
Fixings
- 50 x M3 x 10mm pan head screws (Amazon)
- 50 x M3 x 20mm pan head screws (Amazon)
- 2 x M3 x 6mm pan head screws (Amazon)
- 2 x M3 x 35mm pan head screws (Amazon)
- 35 x M3 Nyloc nuts (Amazon)
- 35 x M3 Hex nuts (Amazon)
Motors, Electronics and Accessories:
- 4 x NEMA17 Stepper Motor
- 1 x 3pcs Endstop Switch
- 1 x SKR v1.3 32bit
- 1 x LCD Display with SDcard reader
- 4 x A4988 With Heat Sink
- 1 x 12V DC 50mm Blow Radial Cooling Fan
- 1 x Heatbed Aluminium MK3 12V 24V
- 1 x 12V 30A 360W Switching Power Supply
- 1 x Thermistor 100K With 1M Cable for Heat Bed
- 1 x DC power wire (choose 14AWG)
- 1 x 10M Tinned Copper 22AWG 2 Pin Red Black
- 1 x 4pcs Bed levelling screw/spring/knob
- 1 x Genuine E3Dv6 or Clone (1.75mm long) with optional Block & Sock v6 Upgrade
- 1 x Inductive Proximity Sensor - PNP
Print settings:
- 3 Perimeters
- 3 top/bottom layers
- 0.2mm layer height (or better)
- 50% infill
- No support required
Print 1 of everything except below:
- 2 x Z_Carriage_v1.1
- 4 x Z_Carriage_Clamp_v1.1
- 4 x Z_Shaft_Clamp_v1.2
- 2 x XY_Clamp_v1.1
- 2 x XY_Joiner_v1.1
- 2 x XY_Idler
- 3 x Y_Shaft_Clamp
- 4 x Bed_Support_v1.1
- 2 x Dual_Bushing_Holder
Some useful extras:
HyperCube 3D Printer Accessory Pack
HyperCube CNC Toolheads
Various Z nut mounts for Integrated Leadscrew Motors
X-Axis 10mm Anodised Aluminium alternatives
If you can't find 10mm x 360mm anodised aluminium tubes for X axis, and besides using Carbon Fibre tubes, there are 2 alternatives:
HyperCube XY_Joiner for 8mm rods on X-Gantry
X Carriage Mod for 3/8" Rod and Bearing for HyperCube 3D Printer
Notes:
- Bed_Support_v1.1 for revised bed configuration (build log video #11)
- Z Endstop v1.1 for revised bed configuration.
- Z_Motor v1.1 and Z_Shaft_Clamp v1.1 for bottom mounted motor
- Fan_Duct v1.1 with extra clearance for E3D silicone socks
- Fan_Duct v1.2 for easier bridge printing
- X-Carriage v1.1 provides extra support to belt mount.
- XY Joiner/Clamp v1.1 supports longer bearing LM8LUU and dual LM8UU bearings.
- Configuration.h files updated to Marlin 1.1-RC8
- Removed old file versions. Can be found here http://www.thingiverse.com/thing:2013921
- E3D (Inductive) Sensor Mount v1.1 for improved sensor mount stability
- New X_Carriage & E3D_Mount & E3D_Sensor_Mount for removable tool heads!
- Z-axis rails increased to 12mm diameter, Z-axis parts updated.
- Marlin 1.1.9 Configuration.h files
- Added Bowden parts to this HyperCube kit
- Bowden_Motor_v1.1 easier to print (62deg overhang)
Enjoy this design? Consider supporting me on Patreon: https://www.patreon.com/Tech2C