QuickClamp
par lynxdvm
Fichiers imprimables (25)
-
stlQuickClamp_20.STL
59 Ko · 536 téléchargements
-
stlQuickClamp_21.STL
56 Ko · 535 téléchargements
-
stlQuickClamp_22.STL
64 Ko · 543 téléchargements
-
stlQuickClamp_23.STL
75 Ko · 525 téléchargements
-
stlQuickClamp_24.STL
58 Ko · 526 téléchargements
-
stlQuickClamp_25.STL
69 Ko · 529 téléchargements
-
stlQuickClamp_26.STL
68 Ko · 531 téléchargements
-
stlQuickClamp_27.STL
56 Ko · 526 téléchargements
-
stlQuickClamp_28.STL
71 Ko · 540 téléchargements
-
stlQuickClamp_29.STL
68 Ko · 527 téléchargements
-
stlQuickClamp_30.STL
70 Ko · 536 téléchargements
-
stlQuickClamp_31.STL
67 Ko · 528 téléchargements
-
stlQuickClamp_32.STL
75 Ko · 531 téléchargements
-
stlQuickClamp_33.STL
86 Ko · 533 téléchargements
-
stlQuickClamp_34.STL
69 Ko · 528 téléchargements
-
stlQuickClamp_35.STL
79 Ko · 521 téléchargements
-
stlQuickClamp_36.STL
79 Ko · 527 téléchargements
-
stlQuickClamp_37.STL
66 Ko · 532 téléchargements
-
stlQuickClamp_38.STL
82 Ko · 526 téléchargements
-
stlQuickClamp_40.STL
53 Ko · 528 téléchargements
-
stlQuickClamp_42.STL
58 Ko · 529 téléchargements
-
stlQuickClamp_44.STL
52 Ko · 529 téléchargements
-
stlQuickClamp_46.STL
62 Ko · 525 téléchargements
-
stlQuickClamp_48.STL
65 Ko · 530 téléchargements
-
stlQuickClamp_50.STL
63 Ko · 529 téléchargements
Description
Ever struggled with a G-clamp to secure something to your work bench? No more struggles with the QuickClamp! Simply place the clamp over your object and slide them over the bench's edge. Quick... Easy... Secure!!!
I have created a multitude of different sizes clamps. There should be one for your purpose!
How to select a clamp:
Add the thickness of your bench or table top to the thickness of the object to be clamped and select the clamp with that number. For example, my desk top is 29mm thick and the object is 4mm thick - So I use a 33 Clamp (28+4=33).
Material:
I've found ABS or PETG is the best. It needs material with some flexibility and PLA has a tendency to break before it bends.
Printing:
For optimum strength and rigidity I use 5 solid top layers, 5 solid bottom layers, 5 perimeter shells and 50% infill. No cooling. No supports.
Problem - too tight:
- Sand off some of the inside of the top square and bottom curvature (open up the gap a bit)
- Print with fewer solid layers, perimeters and less infill
- Use a size bigger clamp, or
- Scale the Y-direction to about 103%
Problem - too loose:
- Use a size smaller clamp, or
- Scale the Y-direction to about 97%
Tip: I design the things I want to hold down (e.g. my helping hands - to be published soon) with a consistent clamp height of 4mm. I also add a 16X16mm square recess of 1-1.6 mm deep to further secure the object and prevent sliding or turning. This way, I only need 1 clamp for all the different items to be secured.