Cyclone SYSClone
par ArjanNieuwenhuis
Fichiers imprimables (16)
-
stlSys_2_t-loc_Cyclone_Suction_Top_Brackets.stl
71 Ko · 1 237 téléchargements
-
stlSys_2_t-loc_Cyclone_Base_part2.stl
147 Ko · 1 253 téléchargements
-
stlSys_2_t-loc_Cyclone_Suction_loft.stl
515 Ko · 1 231 téléchargements
-
stlSys_2_t-loc_Cyclone_Base_part1.stl
467 Ko · 1 320 téléchargements
-
stlSys_2_t-loc_Cyclone_Inside_part.stl
122 Ko · 1 270 téléchargements
-
stlSys_2_t-loc_Cyclone_Top_Lid.stl
395 Ko · 1 264 téléchargements
-
stlSys_2_t-loc_Cyclone_Intake_Loft.stl
486 Ko · 1 233 téléchargements
-
stlSys_2_t-loc_Cyclone_Suction_Top_Tube.stl
262 Ko · 1 222 téléchargements
-
stlSys_2_t-loc_Cyclone_Systainer_ports_58_mm.stl
187 Ko · 1 198 téléchargements
-
stlSYSClone_systainer_template.stl
209 Ko · 1 172 téléchargements
-
stlSysclone_template_letters.stl
145 Ko · 1 170 téléchargements
-
stlSYS1_t-loc_LATCH.stl
1.4 Mo · 1 195 téléchargements
-
stlSYS_2_t-loc_Sysclone_latch_cover.stl
160 Ko · 1 183 téléchargements
-
stlSYS_t-loc_Reinforcement_Left_side.stl
120 Ko · 1 207 téléchargements
-
stlSys__t-loc_Cyclone_Reinforcement_stabalizer.stl
489 Ko · 1 184 téléchargements
-
stlSYS_t-loc_Reinforcement_Right_side.stl
123 Ko · 1 189 téléchargements
Description
Cyclone that will fit inside Sysainer t-loc 2
REQUIRED : 300mm x 300mm bed size.
i printed this on a Ender 3 Max
support that is needed varies part to part.
infill also varies from part to part.
Infill % / support / type of brim i used / type of ironing the part is listed below, including estimated print time for each part
Sys 2 t-loc Cyclone Base part#1 ABS 40% infill_in+out Brim 0.2 mm layer + iron 0.2 + Support 19h.30min
Sys 2 t-loc Cyclone Base part#2 ABS 40% infill_in+out Brim 0.2 mm layer + iron 0.2 + Support 6h.21min
Sys 2 t-loc Cyclone Inside part ABS 50% infill_Brim_0.2 layer_6h.23min
Sys 2 t-loc Cyclone Intake Loft ABS 25% infill Brim 0.2 Layer 4h.9min
Sys 2 t-loc Cyclone Lid Brackets ABS Brackets 20% infill + Brim 0.2 + iron 0.2 1h.45Min
Sys 2 t-loc Cyclone Suction loft ABS 25% infill + Brim 0.2 Layer 3h.50min
Sys 2 t-loc Cyclone Suction Suction Tube ABS 25% infill in+out Brim_Support_0.2 MM 6h.40min
Sys 2 t-loc Cyclone Systainer Tube ABS 40% infill in+out Brim 0.2 + iron 0.2 3h.30min
Sys 2 t-loc Cyclone Top part ABS 40% infill + brim_0.2 layer+infill#2-layertopmost ironing 0.2+COLOUR CHANGE_17h.22min
Sys 2 t-loc Cyclone Tubes+Internal part_ABS 40% infill brim 0.2 layer + infill#2-layer+support_24h.0min
SYS1 t-loc SET OF 2 Sysclone Latch ABS 60% infill + Support + 0.15 layer + iron 0.1 11h.24min
SYS1 t-loc Sysclone Latch ABS 60% infill + Support + 0.15 layer + iron 0.1 5h.40min
you need approximately 1Kg of 1.75 mm filament
i strongly suggest to start printing the systainer dust ports, so you can see if your printer is accurate to accept the 58 mm hose connection from a Festool vac.
dust ports will accept 58 mm connector
you do need to do a little assembly:
Note: The inside part is connected to the lid with m40 thread , this thread is thin and only meant to keep the 2 pieces at the right location and hold them together till glue set up.
bottom part 1 and 2 should be assembled, broke this part up so it doesn't need as much support
the brackets supposed be mounted on top of the lid, underneath the top out lead tube
you do need to create some holes in your systainer , i was going to sandwiche the base of sys 2 , the lid of a sys 5 and the cyclone base part 1 together using m6 bolts with washers and nuts .but i might just put the base part in the top systainer using silicone.
i also added a expansion foam ring between the two systainers to make sure there is no leakage between them.
the holes in the corner on the bootom need to be closed, its an open channel to the inside of the systainer.
there also needs to be some kind of support in the collection systainer to prevent its pulling together,i think i will use an original lid insert, and make some kind of wood inlay to prevent it to collaps under the negative pressure, still working on that part but i will update when its working
once the collection systainer is full, you can easily open the t loc and empty it.
if you printed it out, and you are pleased with it, please let me know in the comments, also credits are very much appreciated!