SMARTPHONE UNIVERSAL SUPPORT

I. SMARTPHONE UNIVERSAL SUPPORT ( SUS )

More detailed instructions in PDF. ( Page 1-7 )
https://1drv.ms/b/s!Ary5van2EnpxpiXwRIRa26MRl3tC

This universal support for smartphone of 65 to 85 mm wide.
ideally put the phone with its case to protect it better
By means of an adjustable support and a screw clamp, the mobile can be oriented and fixed in various types of surface.
My idea is that most of the sets or pieces printed in 3D can also have other uses. For example; adding an adapter to the SUB I can mount the mobile on a bicycle or on a motorcycle, or when changing a piece of SBS I can mount the mobile on a tripod, etc.

If you want some pieces to be durable, I recommend using PETG or ABS on parts that work outside, such as accessories for bicycles or motorcycles that I will add later.

I am sorry to use a lot of metal screws, but it is necessary for a reliability and robustness of the set, I will try to unify and detail as best as possible.

The Smartphone Universal Support consists of three parts :

1. SMARTPHONE UNIVERSAL BASE ( SUB ), It is the set of pieces where the mobile is placed and adjusted.
2. SMARTPHONE BASE SUPPORT, ( SBS ), It is where the universal Smartphone base is connected, and that it allows to rotate, regulate and fix the SUB to capture videos, etc., it can also have other utilities.
3. SCREW CLAMP ( SC ), is to fix the SBS to a table, chair, door, bar, etc. but it can also be used for other utilities.

1.- SMARTPHONE UNIVERSAL BASE ( SUB )

Printed parts.

• 1 x SUB1- Base
• 1 x SUB2- Side Guide
• 2 x SUB3- M3 Nut Wrench
• 1 x SUB4- Top Guide L ( 151-165 mm Smartphone lenght)
or SUB7- Top Guide S7 edge(camera)
• 1 x SUB5- Cylindrical Adapter
• 1 x SUB6- M6 Nut Wrench

Hardware

• 2 x Allen head screws M3 x 15
• 5 x Nuts M3
• 4 x Flat washers M3
• 1 x Conic head screw M3 x 25
• 1 x Allen head screw M3X30 (full threaded)
• 1 x Hexagonal head screw M6 x 30
• 1 x Nut M6
• 1 x Flat washer M6

2.- SMARTPHONE BASE SUPPORT ( SBS )

Printed parts.

• 1 x SBS1- Top turn adapter
• 1 x SBS2- Bottom turn adapter
• 1 x SBS3- M6 Nut Wrench
• 1 x SBS4- M8 Nut Wrench

Hardware

• 1 x Hexagonal head screw M6 x 30
• 1 x Nut M6
• 1 x Flat washer M6
• 4 x Nuts M8
• 1 x Threaded rod M8 x 100, 150, 200, 250, etc (length to choose)

3.- SCREW CLAMP ( SC )

Printed parts.

• 1 x SC1- Clamp Frame
• 1 x SC2- Clamp Cap
• 1 x SC3- Nut cover
• 1 x SC4- Screw Handle M8

Hardware

• 1 x Hexagonal Head Screw M8x 80 mm
• 1 x Nut M8

...............................................................................
Notes.
..............................................................................

• You can always print only the parts you want or need.

• I try to make the printed nuts wrench (M3, M6, M8, etc. are standard, that is, they are the same for other accessories, so I recommend printing some

• Always try when tightening a nut wrench, always with metal-plastic contact or place a metal washer if it is plastic-plastic to tighten better.

• I do not speak English, I'm sorry for the mistakes, I'm practicing little by little
  .....................................................................................................................

Other applications with the Smartphone Universal Supports ( SUS )

I. Smartphone universal Supports ( SUS )

II. Bike Smartphone holder ( BKS ) for Bike
https://www.thingiverse.com/thing:3679608

III. Motorcycle Smartphone Holder ( MS ) for motorcycle
Soon...

IV. Garmin Support For Bicycle (GS) for GPS Garmin
Soon ....................

V. Handle for Smartphone Universal Support (HSUS)
https://www.thingiverse.com/thing:3741800