Flatpack Deck holder System
door TechnoPallidin
Printbare bestanden (30)
-
stlFlatPack_Mini_Half_Side_H3.stl
101 Ko · 369 downloads
-
stlFlatpack_Standard_3x1_Side.stl
100 Ko · 401 downloads
-
stlFlatpack_Mulit_Standard_Back_Panel_2x2.stl
328 Ko · 391 downloads
-
stlFlatpack_Multi_Standard_Bottom_Panel_2x2.stl
303 Ko · 387 downloads
-
stlFlatpack_Mini_2x1_Back_Panel.stl
195 Ko · 389 downloads
-
stlFlatpack_Multi_Standard_3x_Back.stl
433 Ko · 401 downloads
-
stlFlatpack_Multi_Standard_Front_Panel_2x2.stl
315 Ko · 388 downloads
-
stlFlatpack_Standard_2x1_Side.stl
66 Ko · 391 downloads
-
stlFlatpack_Multi_Standard_3x_bottom.stl
404 Ko · 395 downloads
-
stlFlatPack_Mini_Bottom_2x.stl
285 Ko · 387 downloads
-
stlFlatpack_Multi_Standard_3x_Front_.stl
424 Ko · 398 downloads
-
stlFlatpack_Standard_2x1_Back_Panel.stl
200 Ko · 387 downloads
-
stlFlatpack_Standard_2x1_Bottom.stl
187 Ko · 389 downloads
-
stlFlatpack_Multi_Standard_Side_H3.stl
101 Ko · 394 downloads
-
stlFlatpack_Standard_2x1_Front.stl
197 Ko · 388 downloads
-
stlFlatPack_Mini_Half_Depth_2x1_Side.stl
75 Ko · 387 downloads
-
stlFlatpack_Mini_2x1_Bottom.stl
186 Ko · 390 downloads
-
stlFlatPack_Mini_Half_Depth_2x1_Bottom.stl
185 Ko · 389 downloads
-
stlFlatpack_Mini_2x1_Front.stl
195 Ko · 389 downloads
-
stlFlatPack_Mini_Half_Bottom_2x.stl
282 Ko · 362 downloads
-
stlFlatPack_Multi_Standard_Side_H2.stl
78 Ko · 392 downloads
-
stlFlatPack_Mini_Half_Depth_3x1_Side.stl
98 Ko · 387 downloads
-
stlFlatPack_Mini_Half_Front_2x.stl
304 Ko · 364 downloads
-
stlFlatPack_Mini_Back_X2.stl
298 Ko · 363 downloads
-
stlFlatPack_S_x1_Bottom.stl
187 Ko · 381 downloads
-
stlFlatPack_S_x1_Front.stl
197 Ko · 380 downloads
-
stlFlatPack_S_x1_Back.stl
200 Ko · 381 downloads
-
stlFlatpack_Multi_Double_Depth_H2.stl
59 Ko · 354 downloads
-
stlFlatpack_Multi_Double_Depth_Bottom_x2.stl
321 Ko · 334 downloads
-
stlFlatpack_Multi_Double_Depth_Bottom.stl
211 Ko · 328 downloads
Beschrijving
Update 9/13/2020 I have uploaded a double depth for the standard card sizes. 2 Tier sides and a single and double width bottom. The Back and Front for the Multi set use the standard back/front that are already present.
Update 5/20/2020 I have uploaded more for the multi-row sets. Included are standard depth 3 high side and standard size 3 wide panels. This will allow a holder to have up to 9 decks in a single holder. I can go bigger but this is the limit of my printers. I also included a 3 high American Mini side which can be used with the Mini Half panels. The Mini full panels should fit the same side as the standards. As time goes by I'll add more, if you find a configuration I don't have that you would like to see leave a comment and I'll see what I can do.
Update 5/13/2020 I have uploaded the first multi-row set. This is for the Standard card set. 2x2 setup. Now that I have this one done I'll start work on the others. For this particular item, print 2 backs, 2 bottoms, 1 front and 3 sides (H2). You slide the bottoms through the sides and push back to "lock" the front/back panels will lock the bottoms in place.
Update 5/10/2020 I have updated to include the American Mini (zombicide size) cards. With this update I have a single row, 2 deep standard depth (about 1"), 2 deep half depth, and a 3 tier half depth set. I'm currently working on some more layouts including multi-row, so a 4 deck holder that's 2 tier as an example. Hopefully will have one to start with as test prints are going now.
Update 5/9/2020 I have changed this thing to be a "System" as I intend to upload extra combinations to give players variability. Included in this update is a 3 tier side panel. My next update will be sized for american "mini" cards. Think zombicide, massive darkness, etc. From there I intend to start on multi-row holders. Starting with a 2x2 then 3x2. Will see if I go further as I'm sizing everything to easily fit on printers as much as possible. I will also be including some different widths as well.
I designed this to create a Card holder for all my board games to make table pretense easier to deal with and also make it collapsible so that I don't have to store large card holders. This will hopefully be the first of many designs.
These designs will be set to hold up to sleeved cards for each type I setup. If there are other sizes you would like to see, just comment and I will see what I can do.
Standard Sized Cards
Standard sized cards I'm considering to be roughly 66mm wide "sleeved" as most standard sized cards are roughly 63mm wide. Depending on your calibration of your printer you may be anywhere between 65-67mm wide. My standard design is set to 67mm wide for the "inside" dimension. As long as your final product is roughly 66.5mm it shouldn't be an issue.
All parts with Standard in there name will fit together as long as you use the same row depth. This might change once I get to multi Row.
You can currently build a 2 tier and 3 tier standard depth set using the components here. The Back, Front and Bottom panels are the same for both sets, just different side panels are needed.
American Mini Cards
Mini card holders are now live. I currently have a 2 tier and 3 tier setup, 3 tier is only for half depth currently. With a full depth (1" roughly) and a half depth setup.
For both sizes all the Bottom, Front and Back panels are interchangeable. Just choose your side panels accordingly.
You could potentially use the 3 tier sides for full depth from the standard cards as the parts will fit, however I found I needed to adjust the height of the holder since mini cards are smaller (height) and while it does work its not as optimized.
Assembly
Assembly for these are straight forward, slot the bottoms into the side panels and then slide in the front/back panels.
Coming Soon
I currently have new multi-row or column however you want to look at it, coming soon. I'm currently working on a 2x2, so four decks, setup for standard sized cards. I will carry the design forward to the other sizes as well. Just takes me some time.