OB1.4 open beam 3D printer
par Wired1
Fichiers imprimables (29)
-
stl14LCorner.stl
323 Ko · 29 487 téléchargements
-
stl14RCorner.stl
684 Ko · 29 164 téléchargements
-
stl14LTopVert.stl
203 Ko · 29 115 téléchargements
-
stl14RTopVert.stl
203 Ko · 29 089 téléchargements
-
stl14ZLTop.stl
287 Ko · 29 088 téléchargements
-
stl14ZRTop.stl
417 Ko · 29 033 téléchargements
-
stl14Zmotor.stl
145 Ko · 29 062 téléchargements
-
stlCornerplateL3.stl
346 Ko · 29 028 téléchargements
-
stlCornerplateR3.stl
349 Ko · 28 986 téléchargements
-
stlY_roller1b.stl
33 Ko · 29 042 téléchargements
-
stlYbarEnd.stl
112 Ko · 29 051 téléchargements
-
stlYidler.stl
136 Ko · 28 998 téléchargements
-
stlZmotor.stl
357 Ko · 29 061 téléchargements
-
stlXidler2.stl
595 Ko · 28 951 téléchargements
-
stlXmotor3.stl
370 Ko · 29 091 téléchargements
-
stlJ_daptor2S.stl
24 Ko · 28 644 téléchargements
-
stlYmotor.stl
224 Ko · 28 656 téléchargements
-
stlOB14Y1.stl
899 Ko · 28 822 téléchargements
-
stl4511gearsR.stl
605 Ko · 28 462 téléchargements
-
stlS_Quikfit_Jhead_block.stl
48 Ko · 28 390 téléchargements
-
stlSQF1.9c_fixed.stl
339 Ko · 28 406 téléchargements
-
stlSQuikfitidler1.9c_fixed.stl
128 Ko · 28 336 téléchargements
-
stlX_Switch.stl
65 Ko · 28 372 téléchargements
-
stlY_Switch.stl
62 Ko · 28 384 téléchargements
-
stlZ_Switch.stl
42 Ko · 28 375 téléchargements
-
stlOBXcarry20.stl
369 Ko · 28 253 téléchargements
-
stlOBXblock1.stl
188 Ko · 28 065 téléchargements
-
stlAzteegX3_holder_2.stl
475 Ko · 27 998 téléchargements
-
stlPushClamp2.stl
75 Ko · 28 024 téléchargements
Description
This is my second printer design and is based on my first printer the OB1 with a reengineered top end. The 1.4 features greatly increased build height and now has a massive build volume of 200mm x 200mm x 200mm (8" x 8" x 8") with an open front design yet is still 100% printable on an existing reprap printer.
The aim here was to make a larger volume printer that did not need specialist parts, laser cutting or CNC machinery to make. The 1.4 designation comes from the new side frames resembling the number '4'.
If you have already built the earlier OB1 printer you can reuse a lot of the original plastic parts as well as all of the extrusions although this new printer uses less extrusion and some will require shortening.
The x-axis ends and carriage are now included but have not yet been tested hence the "work in progress" label.
I may yet design a standard x-carriage to take a Wades type extruder but if anyone else wants to have a go the X-axis rails are 55mm spacing 8mm diameter linear rods.