OB1.4 open beam 3D printer
por Wired1
Ficheiros imprimíveis (29)
-
stl14LCorner.stl
323 Ko · 29 487 descargas
-
stl14RCorner.stl
684 Ko · 29 164 descargas
-
stl14LTopVert.stl
203 Ko · 29 115 descargas
-
stl14RTopVert.stl
203 Ko · 29 089 descargas
-
stl14ZLTop.stl
287 Ko · 29 088 descargas
-
stl14ZRTop.stl
417 Ko · 29 033 descargas
-
stl14Zmotor.stl
145 Ko · 29 062 descargas
-
stlCornerplateL3.stl
346 Ko · 29 028 descargas
-
stlCornerplateR3.stl
349 Ko · 28 986 descargas
-
stlY_roller1b.stl
33 Ko · 29 042 descargas
-
stlYbarEnd.stl
112 Ko · 29 051 descargas
-
stlYidler.stl
136 Ko · 28 998 descargas
-
stlZmotor.stl
357 Ko · 29 061 descargas
-
stlXidler2.stl
595 Ko · 28 951 descargas
-
stlXmotor3.stl
370 Ko · 29 091 descargas
-
stlJ_daptor2S.stl
24 Ko · 28 644 descargas
-
stlYmotor.stl
224 Ko · 28 656 descargas
-
stlOB14Y1.stl
899 Ko · 28 822 descargas
-
stl4511gearsR.stl
605 Ko · 28 462 descargas
-
stlS_Quikfit_Jhead_block.stl
48 Ko · 28 390 descargas
-
stlSQF1.9c_fixed.stl
339 Ko · 28 406 descargas
-
stlSQuikfitidler1.9c_fixed.stl
128 Ko · 28 336 descargas
-
stlX_Switch.stl
65 Ko · 28 372 descargas
-
stlY_Switch.stl
62 Ko · 28 384 descargas
-
stlZ_Switch.stl
42 Ko · 28 375 descargas
-
stlOBXcarry20.stl
369 Ko · 28 253 descargas
-
stlOBXblock1.stl
188 Ko · 28 065 descargas
-
stlAzteegX3_holder_2.stl
475 Ko · 27 998 descargas
-
stlPushClamp2.stl
75 Ko · 28 024 descargas
Descrição
This is my second printer design and is based on my first printer the OB1 with a reengineered top end. The 1.4 features greatly increased build height and now has a massive build volume of 200mm x 200mm x 200mm (8" x 8" x 8") with an open front design yet is still 100% printable on an existing reprap printer.
The aim here was to make a larger volume printer that did not need specialist parts, laser cutting or CNC machinery to make. The 1.4 designation comes from the new side frames resembling the number '4'.
If you have already built the earlier OB1 printer you can reuse a lot of the original plastic parts as well as all of the extrusions although this new printer uses less extrusion and some will require shortening.
The x-axis ends and carriage are now included but have not yet been tested hence the "work in progress" label.
I may yet design a standard x-carriage to take a Wades type extruder but if anyone else wants to have a go the X-axis rails are 55mm spacing 8mm diameter linear rods.