e-NABLE Phoenix Hand v2
von EnableCommunityFoundation
Druckbare Dateien (26)
-
stlgripper_box_right.stl
43 Ko · 59 541 Downloads
-
stlswivel_pin_right_JD1.stl
55 Ko · 58 629 Downloads
-
stlthermo_gauntlet_two_strap_one_row.stl
164 Ko · 59 215 Downloads
-
stlPhoenix_Right_Demo_Bar_V1.stl
435 Ko · 58 262 Downloads
-
stlPhoenix_Left_Demo_Bar_V1.stl
435 Ko · 57 868 Downloads
-
stlfingertip_short_v2.stl
267 Ko · 59 216 Downloads
-
stlwhippletree_JD3.stl
114 Ko · 58 629 Downloads
-
stlfinger_phalanx.stl
115 Ko · 59 184 Downloads
-
stlpalm_mesh_right_thin.stl
731 Ko · 58 241 Downloads
-
stlthumbtip_v2.stl
285 Ko · 58 898 Downloads
-
stlthumb_phalanx.stl
118 Ko · 58 643 Downloads
-
stlwrist_pin_thermo.stl
136 Ko · 58 302 Downloads
-
stlthumb_knuckle_pin.stl
28 Ko · 58 520 Downloads
-
stlretention_clip.stl
58 Ko · 58 194 Downloads
-
stlswivel_pin_left_JD1.stl
183 Ko · 57 617 Downloads
-
stlknuckle_pin_short.stl
30 Ko · 58 456 Downloads
-
stlthumb_v2_tensioner_pin.stl
39 Ko · 58 043 Downloads
-
stlwrist_pin_cap.stl
236 Ko · 58 097 Downloads
-
stlthumbtip_pin.stl
138 Ko · 58 001 Downloads
-
stlknuckle_pin_long.stl
30 Ko · 58 272 Downloads
-
stlgripper_box_left.stl
43 Ko · 57 591 Downloads
-
stlfingertip_pin.stl
138 Ko · 58 416 Downloads
-
stlpalm_mesh_right_thick.stl
732 Ko · 57 586 Downloads
-
stlfingertip_long_v2.stl
276 Ko · 58 652 Downloads
-
stlpalm_right_new_supports.stl
767 Ko · 58 929 Downloads
-
stlpalm_left_new_supports.stl
764 Ko · 58 191 Downloads
Beschreibung
This is a remix of the original e-NABLE Phoenix hand by Jason Bryant with replacement components by John Diamond, Scott Darrow and Andreas Bastian. A full assembly guide is included. The changes from the original are as follows:
- Gauntlet - Original fully 3D printed version replaced with a thermoformed equivalent (lighter, stronger, uses less filament, quicker to print and can be adjusted to better fit the forearm)
- Gripper box components - Whippletree doesn't require tying to the swivel pin using string. The printing support from the swivel pin should be cut/snipped/filed off before assembly. The thumb tensioner pin is shorter so it doesn't need to protrude from the front of the gripper box.
- Thermoformable palm mesh - An easier to assemble alternative to using Velcro in the palm. Can be thermoformed and adjusted to fit the recipient. Two alternative versions, thin/thick, are provided.
- Palm with supports - The support structure uses less filament than the original and can be easily, safely and cleanly removed by hand usually without tools.
- Demo bar - Used instead of the palm mesh if the hand is to be used for demonstration purposes. It allows a person with a full set of fingers and thumb to wear the hand and operate it.
- Wrist pin - This pin has been shortened to allow it to be used with the thermoformed gauntlet.