FlexFlexRail

von topeban

Druckbare Dateien (13)

  • stl

    ft-FlexRail_V_0.1.stl

    570 Ko · 597 Downloads

    Herunterladen
  • stl

    ft-Distance-V_0.1.stl

    108 Ko · 594 Downloads

    Herunterladen
  • stl

    ft-FlexRail_V_0.13.stl

    740 Ko · 596 Downloads

    Herunterladen
  • stl

    Halter-ft-FlexRail_V_0.131.stl

    20 Ko · 590 Downloads

    Herunterladen
  • stl

    Halter-ft-FlexRail_V_0.13.stl

    19 Ko · 591 Downloads

    Herunterladen
  • stl

    Knobs-ft-FlexRail_V_0.131.stl

    782 Ko · 588 Downloads

    Herunterladen
  • stl

    Double-Basic-Block-ft-30mm-V_0.1.stl

    33 Ko · 583 Downloads

    Herunterladen
  • stl

    Halter-L-V_0.132.stl

    48 Ko · 589 Downloads

    Herunterladen
  • stl

    Halter-R-V_0.132.stl

    81 Ko · 586 Downloads

    Herunterladen
  • stl

    10_Knobs-ft-FlexRail_V_0.132.stl

    799 Ko · 592 Downloads

    Herunterladen
  • stl

    Halter-R-V_0.133.stl

    104 Ko · 582 Downloads

    Herunterladen
  • stl

    Halter-R-V_0.132.stl

    81 Ko · 552 Downloads

    Herunterladen
  • stl

    ft-FlexRail_V_0.133.stl

    737 Ko · 592 Downloads

    Herunterladen

Beschreibung

Mod of FlexRail with Knobs on one and both Side.

I have the Idea to use my empty Filament spool for building another Track
for the ball track

Add a "Distance" Part so that enough height between two FlexFlexRail.
This Part is similar to ft 38246 "Bauplatte 15x15 1Z rot" but with 12x10mm
(and a Bad Knob 8-( )

Fischertechnik Steel Balls have a diameter of 12,7 mm.

The Knobs are longer so that no Support Structure is needed
but round knobs are better for slope of the Rail

Streched the Rail to 17mm (ft 15mm) wide outside
and 229,99 mm length (My maximum 8-( )

New Version 0.133 (10 Knobs on both side an it´s possible to glue extra Knob )

Add a minimum Angle Block (Halter) for connecting two FlexFlexRail
with a angle of 5° for the groove.
Angle Block with two cavitys for insert the FlexFlexRail when Angle Block is
fixed (e.g. inside a empty filament Spool)

(To do :Negative Angle Block for mounting on the Outside)
The Height of 58 mm came from the inside of the empty Filament Spool.

When I placed the Knobs on both end of the Rail I don´t realize that two Fischertechnik Blocks have a minimum disctance between the groove of 15 mm (MIddle to Middle).

Add two Version with knobs on the Outside too.
The distance from the outside knobs of two parts is 15 mm and you can use two
Fischertechnik Basic Blocks or the Double Basic Block

If you need a greater height you can strech the Block in the Slicer/Printer Software.
To Do : version with grooves on top and bottom