BLV mgn Cube - 3d printer
von BLV
Druckbare Dateien (122)
-
stlX_carriage_-_Front_plate_For_Chimera.stl
112 Ko · 574 625 Downloads
-
stlX_carriage_-_Front_plate_For_Chimera.stl
112 Ko · 573 897 Downloads
-
stlX_carriage_-_Front_plate_For_Chimera.stl
112 Ko · 573 417 Downloads
-
stlX_carriage_-_Front_plate_For_Chimera.stl
112 Ko · 572 966 Downloads
-
stlX_carriage_-_Front_plate_For_Chimera.stl
112 Ko · 572 576 Downloads
-
stlX_carriage_-_Block_shiled_Twin_fans_for_Direct_Drive.stl
1.5 Mo · 287 260 Downloads
-
stl
X_carriage_-_Block_shiled_Twin_fans.stl
1.4 Mo · 286 840 Downloads
-
stlZ_mount_-_Left_block.stl
329 Ko · 730 700 Downloads
-
stlZ_mount_-_Right_mgn_mount.stl
278 Ko · 730 203 Downloads
-
stlExtruder__-_bondtech_Rear_mount.stl
519 Ko · 729 776 Downloads
-
stlZ_rail_stopper_-_Bottom_Left.stl
499 Ko · 729 358 Downloads
-
stlbottom_grill.stl
784 Ko · 728 916 Downloads
-
stlZ_mount_-_Left_mgn_mount.stl
247 Ko · 728 600 Downloads
-
stlZ_rail_stopper_-_Bottom_Right.stl
499 Ko · 728 186 Downloads
-
stlFront_Panel_-_Buttons_cover.stl
441 Ko · 727 722 Downloads
-
stlFront_Panel_-_Center_leds_back_plate.stl
313 Ko · 727 269 Downloads
-
stlZ_mount_-_Right_block.stl
329 Ko · 726 944 Downloads
-
stlZ_rail_stopper_-_Top_Left.stl
347 Ko · 726 486 Downloads
-
stlAir_scrubber_-_screw_spacer_2.stl
567 Ko · 726 066 Downloads
-
stlBed_frame_cover_-_front_right.stl
572 Ko · 725 782 Downloads
-
stlFront_Panel_-_Center_leds_diffuser.stl
666 Ko · 725 330 Downloads
-
stlFront_Panel_-_Center_plate.stl
627 Ko · 724 954 Downloads
-
stlZ_rail_stopper_-_Top_Right.stl
347 Ko · 724 581 Downloads
-
stlAir_scrubber_-_main_box.stl
1 Mo · 724 153 Downloads
-
stlFront_Panel_-_Left_leds_back_plate.stl
313 Ko · 723 758 Downloads
-
stlAir_scrubber_-_back_cap.stl
809 Ko · 723 369 Downloads
-
stlBed_frame_cover_-_front_left.stl
572 Ko · 723 023 Downloads
-
stlBed_frame_cover_-_Rear_left.stl
572 Ko · 722 625 Downloads
-
stlBed_frame_cover_-_Rear_right.stl
572 Ko · 722 262 Downloads
-
stlFront_Panel_-_Left_leds_Cap.stl
542 Ko · 721 934 Downloads
-
stlAir_scrubber_-_screw_spacer_1.stl
567 Ko · 721 458 Downloads
-
stlFront_Panel_-_right_grill.stl
366 Ko · 721 116 Downloads
-
stlFront_Panel_-_Left_leds_diffuser.stl
666 Ko · 720 707 Downloads
-
stlFront_Panel_-_left_grill.stl
367 Ko · 720 340 Downloads
-
stlFront_Panel_-_Right_leds_Cap.stl
542 Ko · 719 962 Downloads
-
stlFront_Panel_-_Left_plate_for_PanelDue_5.stl
863 Ko · 498 965 Downloads
-
stlFront_Panel_-_Right_leds_back_plate.stl
313 Ko · 719 189 Downloads
-
stlFront_Panel_-_Center_leds_Cap.stl
542 Ko · 718 813 Downloads
-
stlFront_Panel_-_Right_plate.stl
451 Ko · 718 464 Downloads
-
stlLeds_diffuser_-_rear_left.stl
475 Ko · 718 097 Downloads
-
stlFront_Panel_-_Right_leds_diffuser.stl
666 Ko · 717 722 Downloads
-
stlLeds_diffuser_-_front_right.stl
475 Ko · 717 361 Downloads
-
stlLeds_diffuser_-_front_left.stl
479 Ko · 716 997 Downloads
-
stlFront_Panel_-_Smartphone_drawer.stl
629 Ko · 716 643 Downloads
-
stlLeds_diffuser_-_rear_right.stl
479 Ko · 716 273 Downloads
-
stlLeft_motor_40mm_fan_mount.stl
573 Ko · 715 973 Downloads
-
stlLeft_corner_-_Top.stl
613 Ko · 715 770 Downloads
-
stlLeft_corner_-_Block.stl
763 Ko · 715 428 Downloads
-
stlLeft_Tensioner_-_idler_holder.stl
791 Ko · 714 996 Downloads
-
stlLeft_corner_-_cap.stl
158 Ko · 714 572 Downloads
-
stlLeft_Z_motor_mount.stl
527 Ko · 714 259 Downloads
-
stlRight_corner_-_bottom_aux.stl
290 Ko · 713 936 Downloads
-
stlGrill.stl
1.1 Mo · 713 496 Downloads
-
stlRight_Corner_-_cap.stl
112 Ko · 713 156 Downloads
-
stlRight_motor_40mm_fan_mount.stl
573 Ko · 712 784 Downloads
-
stlRight_corner_-_Block.stl
663 Ko · 712 585 Downloads
-
stlNozzle_cleaner_-_main_holder.stl
1.3 Mo · 712 080 Downloads
-
stlRight_corner_-_Top.stl
477 Ko · 711 786 Downloads
-
stlLeft_Tensioner_-_mount.stl
1.7 Mo · 711 524 Downloads
-
stlMain_Cable_Tube_Holder.stl
1.6 Mo · 711 188 Downloads
-
stlRight_Tensioner_-_idler_holder.stl
791 Ko · 710 732 Downloads
-
stlRight_Z_motor_mount.stl
527 Ko · 710 417 Downloads
-
stlX_carriage_-_Bottom.stl
351 Ko · 710 220 Downloads
-
stlLeft_Tensioner_-_tension_wheel.stl
2.2 Mo · 709 698 Downloads
-
stlX_carriage_-_Fan_mount.stl
692 Ko · 709 337 Downloads
-
stlNozzle_cleaner_-_brush_mount.stl
884 Ko · 708 932 Downloads
-
stlX_carriage_-_Rear_plate.stl
159 Ko · 708 750 Downloads
-
stlX_carriage_-_Front_plate.stl
775 Ko · 708 471 Downloads
-
stlX_carriage_-_Top.stl
261 Ko · 708 120 Downloads
-
stlRight_Tensioner_-_tension_wheel.stl
2.2 Mo · 707 663 Downloads
-
stlRight_Tensioner_-_mount.stl
1.6 Mo · 707 347 Downloads
-
stlX_carriage_-_Cable_locker.stl
2.1 Mo · 707 075 Downloads
-
stlX_carriage_-_modified_MK3_fan_blower.stl
2 Mo · 707 226 Downloads
-
stlY_Endstop_-_Front_Left_-_Rear_left.stl
432 Ko · 706 300 Downloads
-
stlX_mount_-_Top_left.stl
864 Ko · 706 009 Downloads
-
stlX_mount_-_Top_right.stl
841 Ko · 705 687 Downloads
-
stlY_Endstop_-_Front_Left_optional.stl
432 Ko · 705 254 Downloads
-
stlX_carriage_-_Block_shield_for_Bltouch-8mm-12mm_sensors.stl
545 Ko · 561 789 Downloads
-
stlX_mount_-_Bottom_right.stl
2.2 Mo · 704 767 Downloads
-
stlX_mount_-_Bottom_left.stl
2 Mo · 704 399 Downloads
-
stlX_carriage_-_Block_shield.stl
604 Ko · 560 809 Downloads
-
step
BLV_mgn_Cube_-_cad_file.step
55.9 Mo · 703 205 Downloads
-
stlBed_Holder_-_Front_left_For_CR-10_bed_M4_screw.stl
1 Mo · 694 896 Downloads
-
stlBed_Holder_-_Front_right_For_Anet_E12_bed_M3_Screw.stl
1 Mo · 694 543 Downloads
-
stlBed_Holder_-_Rear_left_For_Anet_E12_bed_M3_Screw.stl
1 Mo · 694 201 Downloads
-
stlBed_Holder_-_Rear_right_For_Anet_E12_bed_M3_Screw.stl
1 Mo · 693 869 Downloads
-
stlBed_Holder_-_Rear_right_For_CR-10_bed_M4_screw.stl
1 Mo · 693 591 Downloads
-
stlBed_Holder_-_Front_right_For_CR-10_bed_M4_screw.stl
1 Mo · 693 260 Downloads
-
stlBed_Holder_-_Rear_left_For_CR-10_bed_M4_screw.stl
1 Mo · 692 941 Downloads
-
stlBed_Holder_-_Front_left_For_Anet_E12_bed_M3_Screw.stl
1 Mo · 692 615 Downloads
-
stlJig_Main.stl
374 Ko · 691 824 Downloads
-
stl2040_Jig.stl
579 Ko · 691 126 Downloads
-
stl2020_Jig.stl
945 Ko · 690 798 Downloads
-
stlFront_Panel_-_Left_plate_for_Smartphone.stl
737 Ko · 656 151 Downloads
-
stlX_carriage_-_Top_for_BMG_Direct_drive_extruder.stl
220 Ko · 621 910 Downloads
-
stlX_carriage_-_Block_shield_for_BMG_Direct_drive_extruder.stl
587 Ko · 553 917 Downloads
-
stlX_Carriage_-_BMG_Direct_Drive_mount.stl
443 Ko · 621 340 Downloads
-
stlAir_Scrubber_BIG_-_left_bracket.stl
281 Ko · 620 055 Downloads
-
stlAir_Scrubber_BIG_-_right_bracket.stl
281 Ko · 619 763 Downloads
-
stlAir_Scrubber_BIG_-_body.stl
465 Ko · 619 512 Downloads
-
stlAir_Scrubber_BIG_-_back_cover.stl
704 Ko · 619 207 Downloads
-
stlX_carriage_-_Block_shield_for_Left_Zesty_Nimble.stl
552 Ko · 550 607 Downloads
-
stlX_carriage_-_Front_plate_for_Left_Zesty_Nimble.stl
673 Ko · 579 477 Downloads
-
stlX_carriage_-_Front_plate_for_Right_Zesty_Nimble.stl
673 Ko · 579 186 Downloads
-
stlX_carriage_-_Block_shield_for_right_Zesty_Nimble.stl
504 Ko · 578 889 Downloads
-
stl4010_Spitfire_cover.stl
1.8 Mo · 532 820 Downloads
-
stlX_carriage_-_Front_plate_For_Chimera.stl
112 Ko · 532 383 Downloads
-
step
X-carriage_DirectDrive.step
2.3 Mo · 489 328 Downloads
-
stlFront_Panel_-_Left_plate_for_MKS_TFT32_V4.stl
879 Ko · 390 400 Downloads
-
stlFront_Panel_-_Left_plate_for_PanelDue_4.3.stl
544 Ko · 390 094 Downloads
-
stlX_carriage_-_V6_Locker.stl
1.6 Mo · 372 962 Downloads
-
stlX_carriage_-_V6_locker_IR_mini.stl
1.8 Mo · 372 650 Downloads
-
stlX_carriage_-_V6_Locker_BL-touch.stl
2 Mo · 372 462 Downloads
-
stlX_carriage_-_V6_Locker_12mm_Sensor.stl
1.8 Mo · 372 052 Downloads
-
stlX_carriage_-_V6_Locker_8mm_Sensor.stl
1.8 Mo · 371 759 Downloads
-
stlFrame_wires_Holder_-_Big.stl
228 Ko · 368 903 Downloads
-
stlFrame_wires_Holder_-_Small.stl
259 Ko · 368 629 Downloads
-
stlFrame_wires_Holder_-_Normal_Size.stl
266 Ko · 368 388 Downloads
-
step
X_carriage_-_Block_shiled_Twin_fans_for_Direct_Drive.step
1.6 Mo · 236 288 Downloads
-
step
X_carriage_-_Block_shiled_Twin_fans.step
1.6 Mo · 235 912 Downloads
-
stl
X_carriage_shield_for_the_metal_kit.stl
1.3 Mo · 4 777 Downloads
-
step
X_carriage_shield_for_the_metal_kit.step
1.2 Mo · 4 780 Downloads
Beschreibung
Important notice: The Projects has moved to https://www.blvprojects.com
Thank you :)
official site: https://www.blvprojects.com
Facebook page: https://www.facebook.com/groups/BenLevi
direct link to the project: https://www.blvprojects.com/blv-mgn-cube-3d-printer
Hi, my name is Ben Levi and This is: "BLV mgn Cube" open-source 3D printer project.
building your own good and reliable 3D printer is the main purpose of this project. Basically, it's an open front structure CoreXY 3D printer, based on mgn linear rails for maximum accuracy, efficiency, and high print quality.
Notice: I promise to update this Project page on a weekly basis until it will be completed.
Fast, reliable, accurate
The linear bearing and Delrin Wheel Gantry commonly used at most of the low-mid 3d printers as a cheaper solution for linear motion. well, ye.. it's cheaper but at the expense of accuracy and reliability. linear guided rails (mgn rails) are a way more rigid, extremely precise, and smoother then linear bearing or Delrin. shorting print time without compromising on print quality. There seems to be a good reason why they are mostly used with high-end 3D printers. So, i found cheap Chinese mgn rails at Aliexpress and thought to myself why not?Rigid open structure
I focused my efforts on designing an open front structure that will be rigid as a cubic structure but yet giving you easy access to your build plate and prints. the design includes a front belt tensioner to make it even more convenient. It came after spending tons of hours of software simulating and physical stress test.Accessible
All the parts are easy to find, print or make. You will not find in the BOM an expensive CNC special machined parts or parts that are hard to get. most of the parts are printed or you can buy them online / locally. Notice that you can use your own electronics - as long as you have the knowledge to make your FW suitable to the build.Open Source
You don't need to ask for the original CAD files since i already included it inside the project folder. I admire this community and believe that sharing is the main key in order to make this project even better. Feel free to download the CAD files (Step file) and modify, add, remix or improve it as you like. I would appreciate if you could please share it with this awesome community and mark the remixed parts as a "remixed" linked to this project page.Build and print
I spent many hours adjusting the Firmware for this 3D printer and fine-tuning the best slicing profile (Simplify3D) for it. After building this printer you will only need to upload the config files, load your slicing profile and you are good to go.More modular
The design is more flexible then you think. the printed parts and structure designed to be modular. Not only you can choose your Z height - But you can use a much bigger build plate. all you need to purchase a bigger aluminum profile and mgn rails. The provided CAD file will assist you in calculating the right measurements for your customized "BLV mgn Cube" 3D printer.Easy to build?
To be honest, the installation of the rail will take 70% of the build time. you will have to be accurate and spend a few hours aligning the rails, but boy.. the joy you will feel when it prints will worth every minute you spent installing them. To make it easy on you, I made a 3D animation videos as instructions, Information PDF, sketches, and measurements.- balanced budget
The cost was important, therefore the BOM is balanced to give you the best money-value ratio, without compromising on quality. you will find The best 32bit board a 3D printer can have. Excellent stepper motors, sensors and so. you get to choose if you want to have a 5" panel due touch screen or save 80$ and use your smatphone/Tablet screen without losing features.
To your convenience, i added below an Online 3D viewer links.
you will be able to explore the printer and the isolated frame:
Facebook group
You are more than welcome to share your thoughts, build videos/photos and more at the BLV mgn Cube facebook group: www.facebook.com/groups/BenLevi
Latest updates:
03/02/19: added Jigs
06/02/19: Printing orientation description added + image
07/02/19: added Printer size calculator (Excel file) and info
09/02/19: now BOM calculator file supports Threaded rods length
09/02/19: added block shield for Bltouch, 8mm,and 12mm sensors.
09/02/19: front panel for smartphone.stl - fixed
15/02/19: electronics schematics updated (dual extruder + buttons)
16/02/19: added BMG direct drive extruder (3 STL files + instructions)
16/02/19: added Big Air Scrubber - HEPA+Carbon (working on instructions)
17/02/19: renamed back the 8mm/12mm mounts
17/02/19: added walls dimensions pdf
18/02/19: added Calibration Z height guide
25/02/19: added Zesty Nimble front plate and block shield
26/02/19: Belt system V2 updated - Please use only flanged 623zz ball bearing+flip belt.
28/02/19: fixed Z-height calibration guide
08/03/19: added spitfire fan cover
08/03/19: added Front plate for Chimera (not suitable for layer fan/sensor)
18/03/19: Wiring diagram fixed.
19/03/19: added Step file (CAD) for the DirectDrive setup.
20/03/19: added DWG for the (bottom, Rear, sides) Panels
25/03/19: small fix: Front Panel - Left plate for PanelDue 5 STL file
31/03/19: Fw updated - added M80 PS_ON command on startup.
04/04/19: added DXF (vector file) for the enclosure panels.
16/04/19: Wiring diagram updated v3.2
16/04/19: added steppers setup guide for others steppers brand/batches
17/04/19: updated Simplify3D profile v1.2 (added: M81 S1 end script)
17/04/19: added Neopixel wiring diagram (Beta) and Mimasx Code.
01/05/19: added STL panels for PanelDue 4.3 and MKS TFT32 V4 (not supported by duet)
10/05/19: fixed V6 locker by decreasing the fan screws holes to 2.7mm.
11/05/19: added E3D high temp 314x314 bed size
12/05/19: added quick frame wire holders (based on samella design and thing:2576237)
19/05/19: fixed typo - purge message box
24/05/19: added support for Ender-3 bed size
11/06/19: added Hotend and Heated bed PID tuning Quick guide
25/06/19: added picture that demonstrates how to flip the belts on the rear
01/07/19: added a link for all the screws kit
05/07/19: added wiring diagram for using 12v fans on a 24v system
21/07/19: added optional frame reinforcement for higher Z-axis builds
03/08/19: added New updated Neopixel code by Claus Noack - works!
03/08/19: added updated neopixel wiring version 2.2b
09/08/19: added Powerful twin 4010 blower fan option (layers fan) for Bowden and direct!
13/09/19: added step files for the new twin fans
04/09/20: added a new website for the project!!
Where to start?
- Read, understand and prepare yourself
Start with reading the Thing description and "more info links" section, watch the 3d animations, explore the printer 3D model with the 3d viewer, read the pages I linked in the "more info" sections and make sure you understand the printer structure.
- Read, understand and prepare yourself
- Get the parts
The waiting - is the most frustrating part. make sure you got all the needed parts. prepare spares of T-nuts, screws and so on. If you have decided to use your own electronics, make sure you know how to correctly configure the firmware of your board.
- Get the parts
- build
now the building process begins.. Know that it isn't going to be easy as building a pre-made kit. Prepare all the tools you need and please use a good corner alignment tool, it is crucial to have a precise structure for excellent printing results. it is advised to use also the provided JIGS, the assembly will be much easier. Don't forget to tap holes on the corners and check if its an M5/M6 screw (depends on your extrusions manufacture). Take your time when fixing the rails to the extrusions. I found a good quick video tutorial made by 3D distributed: (youtube.com/watch?v=iX0U1ADH0MY) showing an easy way to align parallel rails. Don't forget to reward yourself after the rails installations - you deserve it :)
- build
- Electronics installation
Install your Electronics carefully. Check your connections and wiring diagram closely and make sure everything hooked up correctly. don't make any shortcuts and use the right tools and parts. the Power cable should be the last thing to connect.
- Electronics installation
- Software, Tests and Calibrations
Update you DuetWifi board to the latest version and upload all the provided config to the sd-micro card, then insert it to your board and power up the system. make sure that the Mini IR sensor blinks 4 times right after powering the printer. please don't move the axis before checking endstop response. Try to home the printer - the printer should move to the left and then to the rear for the printer. if it isn't - check ou motors wiring and config. calibrate your Z height and check your sensors reading (temp). Please make sure to do a PID calibration for both the bed and the hotend sensors - This is very important. otherwise, your prints will fail. if everything looks good load filament and print a calibration cube and so on.
- Software, Tests and Calibrations
- print
Enjoy your printer and give her love when needed :)
maintain your printer by greasing the rails with a Synthetic grease with PTFE or sewing machine oil. Keep the rails clean and the belts tight.
Also, Clean your PEI build plate with alcohol after every print. If you are using the Air scrubber - please replace the HEPA filter when needed.
- print
- Post an "I made one" pictures
Show the world your new 3D printer and be proud of your creation:)
I would appreciate if you could please upload your new built 3D printers pics. Knowing that it helped you create your own 3D printer - for me, it's worth all the hard work and many hours that I spent in this project.
- Post an "I made one" pictures
- Remix & Share
I am 100% sure that there are many ways to make this printer even better. this is why I gave you the source file of the Printer. Make it better by sharing your remixed and ideas with this awesome community:)
- Remix & Share
Those are the main resources you will need have:
- a passion for 3D printing (most important)
- Tools
- Technical ability
- spare time
- budget (mid)
BOM - Bill Of Material
Notes:
- Please Be precise and use the correct extrusions without shortcuts. using 2020 profile instead of 2040, may reduce the frame rigidity.
- The BOM below is for 365mm Z height, If you wish to build a different size, then use the Calculator (excel file named: "BLV_mgn_Cube-Frame_calculator.xlsx" can be found at the project Zip file)
- It is recommended to use normal extrusions with mgn rails and NOT V-slot.
- Please let me know if you found any typo/mistake and I promise to fix it ASAP.
- The Blurolls store from Aliexpress has started to offer a Kit for the project. It contains most of the needed electronics, frame, screws, pre-crimped wiring, panels, tube, brackets and more. I think its a pretty convenient solution, especially when part of the deal is genuine Hiwin rails!
- New cheaper BLV mgn Cube (lite) kit based on SKR + tmc2209 spotted on Aliexpress.
Frame
- 9 x 2040 aluminum extrusion 496mm (Wide Beams)
- 3 x 2020 aluminum extrusion 576mm (Aux wide Beams)
- 1 x 2020 aluminum extrusion 460mm (X axis)
- 4 x 2040 aluminum extrusion 560mm (4 corners height beams)
- 2 x 2040 aluminum extrusion 442mm (Z axis)
- 2 x 2020 aluminum extrusion 405mm (bed frame)
- 2 x 2020 aluminum extrusion size: for CR-10 bed: 173mm OR for Anet bed: 142mm OR for E3D High temp size 314x314 bed: 240mm OR for Ender 3 bed: 106mm
Optional: recommended Frame Reinforcement for higher Z axis builds (465mm+):
Other
- 2 x T Shape Bracket 60x60
- 14 x Corner 90 degrees Angle Bracket for 2020/2040
- 100 x aluminum 2020 Brackets 20x20 \ 20x17
Getting the frame Kit:
notice that you may be able to get a much cheaper price for the extrusions locally.
- Alumnium frame kit in 4 colors: Black/Blue/Red/Purple - anodized after cut+Brackets
- Fysetc - frame aluminum profiles Set / Full frame Kit
- Funssor - frame Kit containing all the needed extrusions
- Reprap - Frame Kit with free DHL shipping - not tested yet
- Geckosys.ch - Frame kit (Switzerland, Germany, and Austria)
Screws and bracket kits:
Motion System
Rails
- 5 x Mgn12H Carriage + 400mm Rails (Use Frame calculator for other Z sizes)
Update: Thanks to Jerry.h now we have two good options for rails:
- Set of cheaper rails for 17$ each (i bought it first).
- Set of Hiwin rails which are the best rails exists on earth or Single Hiwin rail
one of the biggest stores on Aliexpress are authorized Hiwin dealer and decided to
offer a full kit of Hiwin rails for 38$ each rail. in my area ii sold 80$ for one rail. if you can afford it - That's a steal! even E3D chose to use Hiwin rails with their builds. (Notice: Hiwin rails should be tested with a load on the carriage)
Stepper Motors (Please ask them to give you a full D-cut shaft!)
- 2 x X/Y Stepper motor: 17HM19-2004S Nema17 0.9deg 46Ncm 2A
- 2 x Z stepper motors: 17HS19-2004S1 59Ncm 1.8deg 2A
- 1 x Extruder stepper motor: 17HS16-2004S1 Nema17 45Ncm 1.8deg 2A
2 x GT2 Pulley 16 Teeth 5mm bore / excellent GT2 pully 16 Teeth (for X/Y steppers)
Where to get the Steppers kit:
- Motor Kit for BLV mgn Cube 3D printer The manufacturer agreed to offer a kit with all the necessary steppers. Please ask for a full D-cut shaft!
- Moon motors kit for BLV project - high quality steppers
- stepper kit for BLV mgn Cube - stepperonline store - not tested yet
- Stepper motors kit from Blurolls store
Note: ask for a full D-cut! or shave X/Y stepper's shaft with a Dremel/file (2 min work).
Belts system (check assembly section):
- 24 X F623 ZZ Flange Ball Bearings - number 2 or 3 option
I recommend flipping the belts at the rear (check the belt system image), please do not use the geared GT2 16T.
note: There is an Amazon seller who sells low-quality 623zz for triple the price!. his bearings are loose and it will ruin your printing experience.
Belts & Threaded rods
- 1 x 4m Gates 6mm GT2 Fiber Glass Reinforced Belt / 4m Gates 6mm GT2 Fiber Glass Reinforced Belt - tested / 2 x 2m 6mm GT2 Reinforced Belt
- 2 x 3D Printer Lead Screw Diameter 8mm Lead8mm 400mm
2 x Aluminum Coupler 8x5x25mm (I prefer this option) or spider couplers
Main Electronics
- 1 x DuetWifi 32bit main board from Filastruder.com
- 1 x PanelDue 5" screen (not the "5i") OR save 80$ and use your phone/Tablet !
- 1 x Mini differential IR Auto leveling sensor / Mini differential IR height sensor
- 1 x Power Supply DC 24V 20A/30A - i use it / Meanwell PSU 24V 450W
- 2 x 3-Pin endstop switch KW11-3Z / Omron high quality endstop switches
- 1 x Heat Insulation 300mm for the bed
- 3 x NeoPixel Ring 16 leds WS2812 Module
- 1 x 5M Silicone Wire Flexible 14AWG Stranded Copper Cables black\red
- 1 x 22 awg wire 4\5 wires 5m
- 1 x 16mm Momentary switch with led 110V/220V (wall voltage)- power icon
- 2 x 16mm Momentary/locking latching switch with led 12/24V - optional
- 3 x best 4010 24V-2Pin DB Bearing OR Cheap fan 24V add 4 for small air Scrubber.
- 1 x 5015 Blower fan 24V ball bearings - 24V-2Pin DB Bearing
- 2 x 4010 blower fans (dual ball bearings) 24v - only for the new twin blower shield
- 1 x 24V to 12V 15A Step Down Converter(only if you got Anet E12 bed)
2 x 120mm fan 24V ball bearings 3000RPM (for the bigger Air Scrubber
Note: Choose your PSU according to your specs
Hotend options - 4 options:
- Trianglelab excellent Quality V6 hotend (1.75 24V PTFE) - had it - read the note.
- Mellow excellent hotend kit (24V teflon) - i use this
- Blurolls good quality V6 hotend
- Cheap v6 hotend clone
Note: For Triangelab hotend change the M305 raw in config.g file
to this: "M305 P1 T100000 B4725 C0.0000000706 R4700"
more info about it under the "Additional Notes" section on this page.
Hotend optional upgrades:
- Fantastic Ruby nozzle - for abrasive materials printing such as Carbon, glow..
- spare part: Semitec 104GT-2 Thermistor / thermistor + connector / cheap Thermistor
- Plated Copper V6 Nozzle for high temp printing as peek..
- Hardened Steel V6 Nozzle for abrasive materials printing
Heated bed system, choose one of the 2 choices:
- Thumb dial wheels M4-for CR bed or M3 for Anet bed
- Bed springs set or Silicone solid Column-need to cut 2mm of the long ones
Note: For those that prefer Duet clone:
Mechanics
- 1 x Good BMG extruder / metal BMG extruder / BMG extruder / Clear BMG extruder
- 1 x 1m Capricorn clone PTFE tube 1.9mm or 2mm id
- 2 X optional: 635zz Ball Bearing for aligning the stepper's shaft
- 3 x Silicone sock - helps keep the nozzle temperature steady
1 x Spring steel sheet 300x310+PEI sheet+magnetic sheet
Screws
note: Usually a large quantity of screws is sold in bulk so i rounded the quantities.
- 300 x M5 10mm Button Head Socket Cap Screw (buy at least 300~350)
- 2 x M5 16mm Button Head Socket Cap Screw
- 4 x M5 35mm Button Head Socket Cap Screw
- 200 x M5 washers
- 4 x M4 40mm Flat Head Machine Screw - only using CR-10 24V bed
- 2 x M4 30mm Hexagon head
- 78 x M3 8mm Socket Head Cap Screw (buy at least 100)
- 4 x M3 40mm Flat Head Machine Screw - only if using Anet E12 12V bed
- 2 x M3 50mm Socket Head Cap Screw
- 13 x M3 35mm Socket Head Cap Screw
- 2 x M3 30mm Socket Head Cap Screw
- 1 x M3 16mm Socket Head Cap Screw
- 5 x M3 16mm Socket Head Cap Screw - Only if NOT using Block cover
- 8 x M3 18mm Socket Head Cap Screw - Only if using the Block cover
- 3 x M3 25mm Phillips round head
- 1 x M3 22mm Phillips round head
- 4 x M3 40mm Socket Head Cap Screw
- 11 x M3 14mm Phillips round head
- 2 x M3 18mm Phillips round head
- 3 x M3 25mm Socket Head Cap Screw
- 2 x M3 10mm Socket Head Cap Screw
- 8 x M3 22mm Socket Head Cap Screw
- 8 x M3 12mm Socket Head Cap Screw
- 283 x M5 T-nut (buy at least 300)
- 2 x M4 Nut
- 40 x M3 T-nut
- 62 x M3 0.5mm Washer (put 2pcs of 0.5mm or one of 1mm washer) (buy at least 100)
- 26 x M3 Nut (buy at least 50)
- 16 x M3 Nyloc
Links To kits that can be useful:
- Full screws kit for the BLV mgn Cube from Blurolls
- Hardware Kit Screws, Nuts and brackets for BLV mgn Cube Project
440pcs Set of M3 Socket Cap head DIN912 screws
Optional and others
- easy fast wires connectors
- 1M Corrugated tube
- optional: Mayitr Black Wrap Braided Cable Sleeve Wear Resistant like prusa
- solid state relay SSR-25DA to turn ON the printer with button
- SSR Heatsink
- optional: DC step-down module LM2596 (if you are going to use 12V fans/ Led strip)
- 5M LED strip 5050 60leds/m 44key waterproof
- Wago Compact Wiring Connector
- activated carbon filter (for the bigger air scrubber)
- 500pcs replacment 3/32'' G10 Hardened Precision Steel balls for mgn12H rails
- 100K NTC 3950 Thermistors (replacment if broken)
- Hepa Filter for ilife vacuum robots for the smaller air scrubber
- Hepa Filter for eufy robovac 11c for the bigger air scrubber
- Soundproofing Foam Acoustic Sound Absorption Tile
Brass brush for Hotend cleaner
The filaments i used :
- NOULEI Silk Filaments | link2
- 1kg PETG transparent green
- 1kg PETG transparent blue
- 1kg PETG transparent black
- 1kg PLA Silver
1gk PLA Silk gold color - The best Silk filament that i have tested so far
Walls / enclosure
How i created the walls / semi-enclosure?
Well, it's cheap and very easy..
You can choose one of those options:
- 4mm Cardboard sheets (cheap)
- KAPA foam boards (cheap)
- aluminum composite panel
- 4mm Plywood sheets
Then apply this adorable Carbon Fiber Vinyl on the board.
you can use M3/M5 screws to secure the board to the panels.
Tools
- MUST have: 90 Degree Corner Clamps if you want a good printing results.
- Cable Cutter
- SN-28B dupont Crimping Tool
- Tapping Kit M3,M4,M5,M6 - mainly for the corners holes
- PTFE Tube Cutter
- Set Wire Copper Terminal
- 10 pairs JST Plug Male to Female Wire Connector for Dupont wires.
- dehumidifier (moisture absorb) for your dry box The best i have tested in my drybox.
- Stainless Steel Digital Caliper
- Set Dupont Wire Jumper Pin Header Connector Housing Kit Male
- Cable Organizer
- TS100 Soldering iron (my favorite)
Belt Tension Meter/gauge - 3d Printed tool
What & How to print
All the parts were designed to be easily printed and most of them would not require support. in order to make it more convenient I added two tools that can help you decide how to print the parts:
- Print Orientation guide - The image below visualize exactly how you should place all the parts on the build plate. Some of the parts will require support such as the Tensioner idler holder, so pay attention before hitting the start print button. you may notice that on some of the parts has text such as: X90, Y-90.. its the rotation value in order to set the part on the build plate correctly.
PDF fils/Images - down below you will find a few sketches of the main components. Each part has his name on with the recommended infill percentage and material to print with.
Common print settings:
Personally, I would recommend printing all the parts with PETG, especially with parts that located in hot areas (heated bed, hotend..).
Using at least:
3 or more walls/outer parameters
3 or more top/bottom layers
and the recommended infill/material suggested below.
Special Thanks to:
- I want to give heartfelt thanks to my lovely wife for encouraging and supporting me throughout the project.
- Huge thanks and appreciation for Tim from Filastruder.com for supporting this project and many more! (you can read more about it here)
- This great community for making this place my second home :) Thank you!
There are no conditions other than the license terms.
You don't have to, but if you insist a small donation will be greatly appreciated.
Thank you :)