CoreXY Cube
by tempo502
Printable files (28)
-
stlZ_stage_carriage_100mm.stl
2.7 Mo · 8 652 downloads
-
stlZ_endstop_holder.stl
312 Ko · 8 519 downloads
-
stlY_endstop_35mm.stl
137 Ko · 8 372 downloads
-
stlY_endstop_38mm.stl
137 Ko · 8 446 downloads
-
stlY_endstop_switch_clamp.stl
70 Ko · 8 428 downloads
-
stlY_endstop_50mm.stl
144 Ko · 8 453 downloads
-
stlY_endstop_47mm.stl
140 Ko · 8 400 downloads
-
stlY_endstop_32mm.stl
134 Ko · 8 431 downloads
-
stlY_endstop_44mm.stl
140 Ko · 8 372 downloads
-
stlY_endstop_41mm.stl
139 Ko · 8 408 downloads
-
stlX_end_44mm_rod_spacing.stl
1.1 Mo · 8 451 downloads
-
stlX_end_70mm_rod_spacing.stl
1.2 Mo · 8 486 downloads
-
stlX_carriage_44mm_spacing_printable.stl
511 Ko · 8 449 downloads
-
stlNozzle_blower_upper.stl
1.1 Mo · 8 411 downloads
-
stlNozzle_blower_lower.stl
80 Ko · 8 420 downloads
-
stlBelt_Clip_left_tensioning.stl
1.9 Mo · 8 425 downloads
-
stlBelt_Clip_right_tensioning.stl
1.9 Mo · 8 393 downloads
-
stlBelt_Clip_flat.stl
964 Ko · 8 452 downloads
-
stlIdler_Bracket_A.stl
272 Ko · 8 426 downloads
-
stlMotor_Bracket_A.stl
746 Ko · 8 406 downloads
-
stlIdler_Bracket_B.stl
272 Ko · 8 400 downloads
-
stlMotor_Bracket_B.stl
745 Ko · 8 348 downloads
-
stlZ_stage_lower_100mm.stl
2 Mo · 8 411 downloads
-
stlZ_stage_upper_100mm.stl
2.8 Mo · 8 394 downloads
-
stlendstop-20x20.stl
88 Ko · 8 371 downloads
-
stlz-endstop-low-profile.stl
277 Ko · 8 349 downloads
-
stlzmount-collar.stl
146 Ko · 8 400 downloads
-
stlNozzle_Blower_Upper_r2.stl
1.1 Mo · 7 562 downloads
Description
BOM updated 8-29-14
This is a reference build for the CoreXY Cube. It's a fast, scalable, high-quality printer that runs Sailfish, utilizes common Replicator Mightyboard clone electronics, and costs about $1000.
There are a number of CoreXY Cube builds "in the wild" now for this basic design, at least 6 that I know of (July 2014). Here's a few:
http://www.thingiverse.com/thing:252041
http://www.thingiverse.com/make:69062
http://www.thingiverse.com/thing:313048
https://www.flickr.com/photos/d-newman/sets/72157645313526624/
I've updated many of the parts and put together a BOM. But the base design is a mix of:
- Ichibey's Sakura CoreCube Hbot modeling work
- Jetguy's lasercutter templates and electrical / extruder configuration
- DNewman's Sailfish programming for CoreXY gantries
Credit should go to the above -- I'm just assembling all the build files for everyone's convenience.
Printer size is flexible. With a 340x340x440mm (outside dimensions) Misumi frame kit, my usable build area is 212x,178y, 195z. Scaling Z just requires longer rods, Z screw, and 2020 pieces. Scaling X or Y will involve longer rods and belts, plus editing the lasercutter template for the bottom board. Not hard.
The parts are available online from a mix of:
- Misumi
- Adafruit
- Ultimachine
- Robotdigg
- Amazon
- Flash Forge USA
- McMaster
- QU-BD
- Ponoko
- Digikey
- Mbot
But you're welcome to customize or find cheaper sources.