Modular mount system
por wojciechsura
Archivos imprimibles (31)
-
stlBase-3.stl
53 Ko · 6 192 descargas
-
stlBase-4.stl
57 Ko · 6 189 descargas
-
stlLong_Angular_Bar.stl
74 Ko · 6 194 descargas
-
stlLong_Fixed_Angle_Bar.stl
66 Ko · 6 195 descargas
-
stlTripodLeg.stl
51 Ko · 6 180 descargas
-
stlSmall_Angular_Bar.stl
82 Ko · 6 200 descargas
-
stlSmall_Base_Leg.stl
12 Ko · 6 173 descargas
-
stlMedium_Bar.stl
71 Ko · 6 186 descargas
-
stlScrew.stl
130 Ko · 6 196 descargas
-
stlLarge_Change_Bar.stl
73 Ko · 6 179 descargas
-
stlMedium_Base_Leg.stl
12 Ko · 6 160 descargas
-
stlMedium_Angular_Bar.stl
73 Ko · 6 172 descargas
-
stlVice_Screw.stl
986 Ko · 6 201 descargas
-
stlVice.stl
428 Ko · 6 206 descargas
-
stlLong_Base_Leg.stl
16 Ko · 6 158 descargas
-
stlTripod.stl
148 Ko · 6 154 descargas
-
stlSmall_Cam_Holder.stl
50 Ko · 6 159 descargas
-
stlMobile_Mount_Base.stl
51 Ko · 6 163 descargas
-
stlMobile_Mount_Slider.stl
25 Ko · 6 161 descargas
-
stlMobileMountScrew.stl
140 Ko · 6 163 descargas
-
stlMicro_Change_Bar.stl
90 Ko · 6 158 descargas
-
stlTorch_Holder.stl
189 Ko · 6 130 descargas
-
stlMedium_Change_Bar.stl
71 Ko · 6 135 descargas
-
stlMedium_Cam_Holder.stl
158 Ko · 6 141 descargas
-
stlSmall_Change_Bar.stl
82 Ko · 6 139 descargas
-
stlSmall_Bar.stl
82 Ko · 6 134 descargas
-
stlVice_Screw_Top.stl
294 Ko · 6 143 descargas
-
stlSmall_Fixed_Angle_Bar.stl
74 Ko · 6 118 descargas
-
stlTripodMount.stl
78 Ko · 6 156 descargas
-
stlLong_Bar.stl
73 Ko · 6 119 descargas
-
stlMedium_Fixed_Angle_Bar.stl
63 Ko · 6 109 descargas
Descripción
This is a set of parts allowing you to mount anything (almost) anywhere. I needed a flexible desktop torch mount and then I just went ahead with more and more parts.
Note, this thing is more a reboot rather than remix - I designed everything from scratch, though general idea follows yyh1002's modular mounting system. Since mine is compatible with GoPro as well, they might be compatible with one another, but I did not tested it.
The package contains of the following:
- Short/Medium/Long bar (60/80/100 mm). Simple bars - working horses of the mount system.
- Short/Medium/Long angular bar - bars with hinge raised above the bar, though both hinges are at the same angle.
- Micro/Small/Medium/Long change bar - regular bar, though one hinge is rotated 90 degrees to the other one. Micro change bar is an "in-place" change bar, with hinges only.
- Base-3, Base-4 - 3-legged or 4-legged stable base - simple mount, just place it on flat surface (desk, floor etc.)
- Short/Medium/Long base leg - legs for bases (40/60/80 mm).
- Screw - general purpose screw, used in almost all places. Use M5x30 screws with hex head and M5 nut.
- Vice + Vice screw + Vice screw top - a vice (see photo). I recommend printing the vice parts with 0.1mm layer height, since there's a thread and ball joint.
- Torch holder - my initial holder for Castorama torch (on photos).
- Small/Medium/Long fixed angle bar - bars with hinges designed to lock themselves on 0/45/90 degrees.
- Mobile mount base / Mobile mount slider - montage for mobile phone. Use M5x60 screw with hex head and a M5 nut.
- Tripod + TripodLeg - a simple 3-legged tripod. Each leg can either end with small foot (TripodLeg) or can be fixed using other part of the system.
- TripodMount - conversion from a regular tripod to my mount system (may not work with all tripods though)
- Small cam holder - micro holder for small camera (eg. Mobius). Use standard tripod screws.
- Medium cam holder - a little bigger holder for camera (eg. compact one). Use standard tripod screws.
Keep in mind to set up parts properly and generally avoid printing hinges pointing to Z axis, because they will be weak and may break easily. Hinges in parts, which need to be printed towards Z axis (such as bases) have a little bigger hinges, but be careful with those too.
Print with supports when needed, they should be easily removable.
Almost all parts tested on PLA / 50% infill.
I include full Fusion360 archive file, such that you may design your own parts. All dimensions are parametrized.