Arrow
por P-Make
Archivos imprimibles (36)
-
stlProp_Center_Foldable.stl
36 Ko · 332 descargas
-
stlWing_tip_Support.stl
158 Ko · 323 descargas
-
stlWing_Outer_Support.stl
162 Ko · 325 descargas
-
stlServo_Fairing.stl
138 Ko · 322 descargas
-
stlNoseMotor_Bk_Support.stl
226 Ko · 323 descargas
-
stlWing_Root_Structure.stl
440 Ko · 322 descargas
-
stlWing_tip.stl
251 Ko · 321 descargas
-
stlWing_Root.stl
540 Ko · 322 descargas
-
stlNoseMotor_Fr_Support.stl
106 Ko · 324 descargas
-
stlElevator_Rhs.stl
1 Ko · 322 descargas
-
stlAileron_Inner.stl
9 Ko · 321 descargas
-
stlWing_Inner.stl
136 Ko · 321 descargas
-
stlServo_Mount.stl
68 Ko · 324 descargas
-
stlBattery_Tray.stl
67 Ko · 323 descargas
-
stlNoseMotor_Fr_Shell.stl
152 Ko · 323 descargas
-
stlCockpit_Structure.stl
208 Ko · 322 descargas
-
stlElevator_Lhs.stl
1 Ko · 321 descargas
-
stlAcc_Tray.stl
89 Ko · 322 descargas
-
stlElevator_Mid.stl
2 Ko · 321 descargas
-
stlServo_Cover.stl
22 Ko · 322 descargas
-
stlTailplane_Structure_Rh.stl
53 Ko · 321 descargas
-
stlNoseMotor_Bk_Shell.stl
26 Ko · 322 descargas
-
stlAileron_Structure_Outer.stl
4 Ko · 322 descargas
-
stlTailplane_Rh.stl
143 Ko · 323 descargas
-
stlTail_Shell.stl
809 Ko · 324 descargas
-
stlCockpit_Shell.stl
149 Ko · 323 descargas
-
stlCanopy_Back.stl
1.1 Mo · 321 descargas
-
stlTail_Shell_Structure.stl
313 Ko · 321 descargas
-
stlAileron_Outer.stl
884 o · 321 descargas
-
stlAileron_Structure_Inner.stl
9 Ko · 321 descargas
-
stlFront_Canopy.stl
1.3 Mo · 323 descargas
-
stlFin.stl
217 Ko · 323 descargas
-
stlFin_Structure.stl
31 Ko · 322 descargas
-
stlWing_Outer.stl
81 Ko · 323 descargas
-
stlCanopy_Front.stl
1.3 Mo · 321 descargas
-
stlWing_Inner_Support.stl
339 Ko · 321 descargas
Descripción
I wanted a practical & lightweight aeroplane that can fly in moderate wind (approx 10-15mph). It works! so I share this design.
The 3d printing is a multi STL setup for most parts using CURA.
Videos
Flying
3d Printing setup
Assembly
Also included a doc file with instructions and a full list of materials needed to complete the project. (Download files section)
Pre-Requisites
This build requires knowledge of radio control aeroplanes with regard to assembly,radio setup and the use of basic tooling. Also requires the knowledge of 3d printing, 3d printing software setup and the handling of PLA.Other items required to build
- Motor - PLANET-HOBBY-JOKER-2826-12-V3-1450-KV
- ESC - HOBBYWING-Flyfun-V5-20A-2-4S
- Folding propellor - SUPER-FOLDING-PROPELLER-SET-8X4-3
- 9g Servos - Servos
- Battery – Lipo 11.1V 700-900 mahr 25C
- Control Linkages - THREADED-CONTROL-ROD-M2-250MM
- Clevises - CLEVIS-M2
- 2mm Self tapping screws - Screws
- 10mm * 2 mm round magnets - DISC-MAGNET-OE10MM
- 10mm Tube - CARBON-FIBER-TUBE-10-8MM-1M
- 8mm Tube - GLASS-FIBRE-TUBE-8-6MM-1M
- Hinge tape - TOPMODEL-Hinge-tape-set
- Glue - Araldite
- Radio control equipment FLYSKY FS-i6X 10CH 2.4GHz RC Transmitter
Tooling required
- Dremel with various cutting/sanding/drilling attachments - Dremel
- Sandpaper 200 grit or similar
- Crafting knife – Model Knife
- Masking tape – Masking Tape
- Straight edge – 90 Degree edge
- Screwdriver to suit screws – Screwdriver set
- Z-bend Plier – Plier