SuperNova RC plane

di Itek

File stampabili (17)

  • stl

    Motor_mount.stl

    239 Ko · 36 917 download

    Scarica
  • stl

    Inner_Wing_Front_Right.stl

    426 Ko · 36 726 download

    Scarica
  • stl

    Center_Front_Right.stl

    829 Ko · 36 856 download

    Scarica
  • stl

    Inner_Wing_Rear_Right.stl

    531 Ko · 36 781 download

    Scarica
  • stl

    Center_center_Right.stl

    648 Ko · 36 727 download

    Scarica
  • stl

    Aileron_Right.stl

    216 Ko · 36 689 download

    Scarica
  • stl

    Outer_Rear_Wing_Right.stl

    539 Ko · 36 690 download

    Scarica
  • stl

    Pusher_Plate_Right.stl

    1.1 Mo · 36 751 download

    Scarica
  • stl

    Vertical_Stabilizer.stl

    699 Ko · 36 648 download

    Scarica
  • stl

    Outer_Wing_Right.stl

    818 Ko · 36 690 download

    Scarica
  • stl

    Center_rear_Right.stl

    713 Ko · 36 610 download

    Scarica
  • stl

    Smaller_Center_center_right_rear.stl

    330 Ko · 36 234 download

    Scarica
  • stl

    Smaller_Center_front_right_front.stl

    568 Ko · 36 292 download

    Scarica
  • stl

    Smaller_Center_center_right_front.stl

    392 Ko · 36 235 download

    Scarica
  • stl

    Smaller_Center_front_right_rear.stl

    428 Ko · 36 221 download

    Scarica
  • stl

    Hinges_ailerons_male.stl

    352 Ko · 34 382 download

    Scarica
  • stl

    Hinges_ailerons_female.stl

    457 Ko · 34 379 download

    Scarica

Descrizione

SuperNova inspired by rcFoamFighters SuperNova foam pusher plane.

Wings are 1 layer shells (0.4mm) with 1 layer cross internal structure (0.4mm).
3D files are of the right side of the plane only. You will need to mirror all the parts to make the left side.
See PDFs.

There are only 3D files for half a plane. Youll have to mirror the files to make the other half of the plane. I used Cura slicer to mirror my files when I printed.

Files with names starting with "smaller" is alternative prints for those who got smaller printers (split in 2 at center compared to the larger parts).

Center of gravity: approx 45,5 cm from the tip of the nose.

I got my plane to 1420 grams incl. electronics (4S 1300mAh).
Parts glue toghether using (sandpaper+) superglue.

My setup in the video:
Turnigy 60A speed controller
Turnigy 2836-2350 motor
7x5 propeller? (a bit uncertain)
4S 1300mAh battery
I guess I was using Hextronic D-MG16 (Size: 29 x 11.2 x 29mm)

September 2022:
All the files I have on this plane. Im sorry about the mess and how the 3D files are generated. I was not very skilled at 3D when model was made...
https://drive.google.com/drive/folders/1tKnnYXnQUQU0UTZOr8GMS3xFT52hQa4Z?usp=sharing

Good luck!

https://youtu.be/5PpQr6V3fSU

Tag

#airplane #controlled #Fighter #jet #plane #radio #radio controlled #rcplane #RC plane