Stackable Battery Holders Improved
di KLXL
File stampabili (22)
-
stlCR2032-Label.stl
119 Ko · 8 066 download
-
stlAA-Label.stl
21 Ko · 8 726 download
-
stlAAA-Label.stl
37 Ko · 8 526 download
-
stlAA-Cover_Extender.stl
44 Ko · 8 520 download
-
stlAA-Cover.stl
66 Ko · 9 483 download
-
stlC-Cover.stl
54 Ko · 8 033 download
-
stlC-Label.stl
23 Ko · 7 927 download
-
stlAAA-Cover.stl
80 Ko · 9 031 download
-
stlCR2032-Cover.stl
163 Ko · 8 292 download
-
stlAA-Base.stl
65 Ko · 9 455 download
-
stlAA-Base_Extender.stl
41 Ko · 8 367 download
-
stlC-Base.stl
69 Ko · 8 018 download
-
stlC-Base_Extender.stl
40 Ko · 7 882 download
-
stlAAA-Base_Extender.stl
41 Ko · 8 230 download
-
stlAAA-Base.stl
65 Ko · 8 941 download
-
stlAAA-Cover_Extender.stl
44 Ko · 8 168 download
-
stlCR2032-Base.stl
205 Ko · 8 337 download
-
stlC-Cover_Extender.stl
44 Ko · 7 899 download
-
3mfCE3_PLA-AAA-Cover.3mf
115 Ko · 8 193 download
-
3mf
CE3_PLA-AAA-Base__Label.3mf
130 Ko · 8 122 download
-
3mf
CE3_PLA-CR2032-Cover.3mf
148 Ko · 8 080 download
-
3mf
CE3_PLA-CR2032-Base__Label.3mf
214 Ko · 8 073 download
Descrizione
This is a remix of all three stackable battery holders designed by adoniram plus a new holder I designed for CR2032 coin-shaped batteries. The idea was to incorporate other ideas I found in various remixes maintaining the original design as much as possible.
I used the solution proposed by 7eggert which adds ramps on both the base and the cover that fix the jams as well as side holes that allow to see if there are still batteries left.
I also added the side borders to the end of the tongue to prevent the batteries from falling to the sides. Finally, I redesigned the way the cover is locked to the base at the bottom to facilitate the assembly. Based on my tests, the jam issue is now gone in all containers.
This printed very well in PLA as follows:
- cover - no supports, face down
- label - no supports, face down
- base - supports (80% overhang angle), back side down
Update Mar 5, 2021: Added new improved cover and base extenders for models AAA, AA and C. They are based on the remix by dlh567. I added the side tabs and an extender for the C-format batteries. Also, cleaned up the thing files:
- removed different size versions for AA and C, leaving the slightly wider version
- made file naming more consistent
Update Feb 10, 2021: A user fed back that when there were few batteries in the AA box they might jam at the exit due to the opening not being wide enough. Although I can't reproduce the issue and believe it might have to do with different printer calibrations, I have uploaded 0.4mm wider parts for AA and C holders (the latter for size consistency).
I have attached some sample Cura projects in case it is useful to anyone.
Note: the CR2032 base on the actual photo is my previous design which doesn't have the side borders on the tongue as I preferred to save plastic and not reprint it.
Someone mentioned in the comments that PLA drained their batteries because PLA is semi-conductive. I haven't faced the issue, but would recommend you store the coin-shaped batteries with their protective sticker on just in case.