Hypercube Evolution Mods

por greatguitartist

Ficheiros imprimíveis (19)

  • stl

    Extruder_Mount_2.0.stl

    399 Ko · 4 499 descargas

    Descarregar
  • stl

    Retainer_2.0.stl

    183 Ko · 4 472 descargas

    Descarregar
  • stl

    X_Carriage_2.0.stl

    1 Mo · 4 502 descargas

    Descarregar
  • stl

    Bed_Bracket_15_CR-10.stl

    114 Ko · 4 493 descargas

    Descarregar
  • stl

    Sensor_Mount_-_Rear.stl

    107 Ko · 4 499 descargas

    Descarregar
  • stl

    Cable_Mount.stl

    67 Ko · 4 483 descargas

    Descarregar
  • stl

    Bottom_Loom_Mount.stl

    110 Ko · 4 468 descargas

    Descarregar
  • stl

    Z_Nut_Braket_2.0.stl

    116 Ko · 4 475 descargas

    Descarregar
  • stl

    RAMPS_mount_2.0.stl

    373 Ko · 4 472 descargas

    Descarregar
  • stl

    RAMPS_Fan_Mount.stl

    459 Ko · 4 492 descargas

    Descarregar
  • stl

    MOSFET_Mount.stl

    78 Ko · 4 471 descargas

    Descarregar
  • stl

    Power_Mount.stl

    114 Ko · 4 477 descargas

    Descarregar
  • stl

    FGSC_3030_Mount_-_Left_2.0.stl

    58 Ko · 4 494 descargas

    Descarregar
  • stl

    FGSC_3030_Mount_-_Right_2.0.stl

    58 Ko · 4 462 descargas

    Descarregar
  • stl

    Bowden_drive_mount_2.0.stl

    177 Ko · 4 473 descargas

    Descarregar
  • stl

    Spool_Axle_Clamp.stl

    87 Ko · 4 461 descargas

    Descarregar
  • stl

    Blower_Fan_Duct_2.stl

    305 Ko · 277 descargas

    Descarregar
  • stl

    Blower_Fan_Duct_1.stl

    1.2 Mo · 246 descargas

    Descarregar
  • stl

    Blower_Fan_Duct_3.stl

    242 Ko · 280 descargas

    Descarregar

Descrição

Update 04/13/2020
Added STLs for Fan Duct. There are 3 designs to choose from and I've included all 3.

While building my own Hypercube, I chose parts I had on hand for the build and had to create/modify designs. I have listed them below:

  • CR-10 Stock bed: Requires a different 15mm bed bracket with M4 holes and room for thumb screw
  • 18mm LCJ18A3 Capactive ABL Sensor: Requires a mounting bracket located in a place which doesn't interfere with overall axes movement
  • 16mm OD Wiring loom: Requires mounting bracket to secure it to the frame
  • Z Nut Bracket: My hypercube required additional slot length on the nut bracket to correctly position the travel nut.

Design changes due to hardware mounting decisions:

  • RAMPS 1.4 - Decided to mount the board to the frame instead of an acrylic sheet like Scott did on his printer. This required me to design a mounting bracket with 50mm fan shroud to cool the DRV8825 step sticks.
  • Bed heater MOSFET: Designed a simple frame mount
  • Bowden Mount: Decided to mount to the Right Rear Top corner, so had to design a new mounting bracket (Pic shows old version. Newer STL uploaded)
  • Separate Bed Heater MOSFET: Designed a simple frame mount
  • Power Supply: Decided to mount to the frame instead of an acrylic sheet, so had to design a mounting bracket similar to the one created by Tech2C for his 2020 build.
  • 12864 LCD: The LCD cannot be mounted to the bottom front of the frame using the existing FGSC mount as it interferes with the bed Z travel. Designed a new 20 deg. mount (It's mounted to the top rear of the frame in the picture, but can be mounted to the bottom front and will clear the bed)
  • Spool Holder Rod Clamp: Didn't like Tech2C's version where the M8 threaded rod is clamped with screws so designed a more robust version that mounts to the frame. Threaded rod is clamped with 2 M8 nuts, one on either side of the rod holder - The nut facing the frame sits in a recessed hole

Changes to the original X Carriage:

  • Added 2 M3 mounting points in the rear between the belt clamps (Needs threaded insert)

Changes to Original Hotend Mount:

  • Removed 12mm Sensor cutout

Z-Probe Offsets to program in Marlin:

X: 0
Y: 75
Z: 0