Pendulum Wall Clock Final v2
por lustertone
Archivos imprimibles (33)
-
stlClock_Face_Multi_v2.stl
2.7 Mo · 11 052 descargas
-
stlHour_Hand_Pendulum_v1.stl
55 Ko · 11 073 descargas
-
stlWinding_Gear_v2.stl
83 Ko · 11 057 descargas
-
stlGear_Esc_Bearing_v3.stl
145 Ko · 11 059 descargas
-
stlM_Reducing_Gear_v3.stl
153 Ko · 11 040 descargas
-
stlWinding_Drum_v1.stl
105 Ko · 11 027 descargas
-
stlHour_Gear_x2_Bearing_v3.stl
200 Ko · 11 036 descargas
-
stlH_Reduction_Gear_Bearing_v1.stl
187 Ko · 11 025 descargas
-
stlMinute_Hand_Pendulum_v1.stl
58 Ko · 11 019 descargas
-
stlDrum_Gear_Bearing_v1.stl
261 Ko · 11 023 descargas
-
stlCrank_Handle_v3.stl
616 Ko · 11 009 descargas
-
stlClock_Frame_B_Pend_v2.stl
596 Ko · 11 017 descargas
-
stlPendulum_Swinger_Clip_v2.stl
50 Ko · 11 036 descargas
-
stlClock_Face_AIO_v3.stl
762 Ko · 10 987 descargas
-
stlWinding_Drum_End_Cap_v3.stl
219 Ko · 10 992 descargas
-
stlSecond_Hand_Pendulum_v1.stl
29 Ko · 10 996 descargas
-
stlWinding_Stop_Clip_v1.stl
41 Ko · 10 979 descargas
-
stlCrank_Handle_Reversed_v2.stl
60 Ko · 10 977 descargas
-
stlCrank_Screw_Reversed_v2.stl
43 Ko · 10 973 descargas
-
stlGear_Drum_Trans_Bearing_v3.stl
106 Ko · 10 975 descargas
-
stlWeight_Bucket_Cover.stl
49 Ko · 10 875 descargas
-
stlSecond_Gear_Bearing_v1.stl
136 Ko · 10 973 descargas
-
stlPendulum_Swinger_Esc_Fork_v2.stl
179 Ko · 10 989 descargas
-
stlWeight_Pulley_Hook_v3.stl
47 Ko · 10 951 descargas
-
stlDrum_Roller_v2.stl
130 Ko · 10 929 descargas
-
stlMinute_Gear_Bearing_v3.stl
155 Ko · 10 932 descargas
-
stlClock_Frame_T_Pend_v2.stl
728 Ko · 10 925 descargas
-
stl3D_Clock_Weight_v3.stl
2 Mo · 10 840 descargas
-
stlWeight_Pulley_v3.stl
142 Ko · 10 846 descargas
-
stlPlanetary_Gear_v3.stl
55 Ko · 10 918 descargas
-
stlPendulum_Swinger_Weight_v1.stl
227 Ko · 10 920 descargas
-
stlWinding_Sun_Gear_v3.stl
258 Ko · 10 848 descargas
-
stlSizzling_Jaiks.stl
5.3 Mo · 10 854 descargas
Descripción
UPDATE: Files for this clock are uploaded. Let me know if you have any questions.
A true remix of the popular TheGoofy mechanical clock. I took the gearing and reconfigured it to work as a pendulum controlled format.
Improvements:
I have added a few improvements to the drive system, the biggest being 3x7x3 bearings on most of the gears to reduce friction down to a minimum. The entire system uses 3mm rods and most of the system uses 3mm x 60mm rods which you can purchase off Amazon so very little cutting is needed to assemble the clock.
I added a second drive gear connecting to the winding drum to reduce the amount of torque that a single gear was creating in the system.
I increased the thickness of the perimeter of a few of the gears slightly so printing would be somewhat improved.
I am currently re-evaluating the re-winding process to improve the efficiency of the process.
The clock face is designed so that up to 4 colors can be used during the printing process by switching filaments at specific print levels.
I am currently running 7lbs of weight to drive the clock. I will most likely be redoing the pendulum weight design since when the clock weight travels downward the pendulum has caught up on the weight cable on a few occasions.
The only lube I have used on this is a little white lithium on the escapement wheel tines so the pendulum escapement fork glides back and forth smoothly. I also added a tiny bit more to the hour/minute/seconds gear shafts so they would not have much friction between them.