Spice Rack Pullout
por spongybob1958
Archivos imprimibles (19)
-
stlspice-top-cap.stl
106 Ko · 15 311 descargas
-
stlspice-bottom-shelf.stl
551 Ko · 15 661 descargas
-
stlspice-top-shelf.stl
872 Ko · 15 329 descargas
-
stlspice-top-railM.stl
60 Ko · 11 818 descargas
-
stlspice-bottom-rail-1X.stl
110 Ko · 15 182 descargas
-
stlspice-bot-rail-endcap-1X.stl
29 Ko · 15 038 descargas
-
stlspice-bottom-rail-2X.stl
216 Ko · 14 881 descargas
-
stlspice-bot-rail-endcap-2X.stl
56 Ko · 14 800 descargas
-
stlspice-bottom-rail-3X.stl
324 Ko · 15 073 descargas
-
stlspice-bot-rail-endcap-3X.stl
84 Ko · 14 998 descargas
-
stlspice-cab-drawer-pin.stl
684 o · 11 736 descargas
-
stlspice-cab-drawer-bottom-shelf.stl
677 Ko · 11 718 descargas
-
stlspice-cab-drawer-track-3X.stl
131 Ko · 11 695 descargas
-
stlspice-cab-drawer-track-1X.stl
45 Ko · 11 652 descargas
-
stlspice-cab-drawer-track-2X.stl
87 Ko · 11 576 descargas
-
stlspice-top-cap-align.stl
103 Ko · 11 832 descargas
-
stlspice-cab-drawer-bottom-shelf-align.stl
590 Ko · 11 756 descargas
-
stlspice-top-shelf-align.stl
644 Ko · 11 784 descargas
-
stlspice-bottom-shelf-align.stl
611 Ko · 11 858 descargas
Descripción
Pullout Spice Rack
I wanted a better way to organize the spices in a cabinet but having it occupy a limited amount of space. I designed this pullout spice rack to allow for one or more pull out shelves for spices. The rack pulls out and rotates 90 degrees in either direction to access your spices. There are two shelves on the rack which allow for the short spice containers on the top and larger round or square bottles on the bottom.
You could obviously put as many of the racks next to each other--making sure you have room to rotate it after you pull it out--but I've created three different sets of bottom rails and end-caps so you can create a single, double, or triple configuration.
NOTE: I did remix the design for one with less printed material: https://www.thingiverse.com/thing:4826878
I think this version also looks a lot more contemporary.
* Modification of Pin Alignment to Allow Stacking
I did a second revision of the design that aligns all the pins for the shelves and cap so that you can stack 0,1, .. N small shelves and then place the cap.
IMPORTANT: Make sure you use the same (bottom, top, cap) wither with the filename of '-align.stl' or without the 'align'.
The STL file names with "drawer" are for the modification below to use metal drawer slides.
Hardware parts
- Small flat head screws to fasten bottom rail and end-cap to cabinet.
- 2 fender washers - 3/16 in. x 1 in.
- Book binding post (15mm size) or equivalent.
* Modification Using Drawer Slides
I'm printing on a Prusa MK3s with a 0.4mm nozzle. For some users, the rails fit fine and don't require a lot of sanding or adjusting. But some of you have mentioned difficulties. If you are having problems with the rails, this modification allows you to used metal drawer slides.
For using drawer slides, print the "drawer" parts (bottom shelf, pin, and track). Because the bottom shelf is slotted to slide out far enough, a pin is placed in the shelf to keep it from rotating around and being slid back in the wrong direction.
Hardware parts
- 8" drawer slides: https://www.amazon.com/gp/product/B07LCBCVWP/ref=ppx_yo_dt_b_asin_title_o01_s00
- 8/32 low head screw and nut (I had to cut the screw to an approximate length of 6mms).